CY7C63310-PXC Cypress Semiconductor Corp, CY7C63310-PXC Datasheet - Page 38

• Manufacturer Part Number: CY7C63310-PXC
• Description: IC USB PERIPHERAL CTRLR 16-DIP
• Manufacturer: Cypress Semiconductor Corp
• Series: enCoRe™IIr

Specifications of CY7C63310-PXC

• Controller Type: USB Peripheral Controller
• Interface: USB
• Voltage - Supply: 4 V ~ 5.5 V
• Current - Supply: 40mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• For Use With: 770-1001 - ISP 4PORT CYPRESS ENCORE II MCUCY4623 - KIT MOUSE REFERENCE DESIGN428-1774 - EXTENSION KIT FOR ENCORE II428-1773 - KIT DEVELOPMENT ENCORE II
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 14-3. P0.2/INT0–P0.4/INT2 Configuration (P02CR–P04CR) [0x07–0x09] [R/W]
Table 14-4. P0.5/TIO0 – P0.6/TIO1 Configuration (P05CR–P06CR) [0x0A–0x0B] [R/W]
Document 38-08035 Rev. *N
These registers control the operation of pins P0.2–P0.4 respectively. The pins are shared between the P0.2–P0.4 GPIOs and
the INT0–INT2. These registers exist in all enCoRe II parts. The INT0–INT2 interrupts are different from all the other GPIO
interrupts. These pins are connected directly to the interrupt controller to provide three edge sensitive interrupts with independent
interrupt vectors. These interrupts occur on a rising edge when Int act Low is clear and on a falling edge when Int act Low is set.
The pins are enabled as interrupt sources in the interrupt controller registers
To use these pins as interrupt inputs, configure them as inputs by clearing the corresponding Output Enable. If the INT0–INT2
pins are configured as outputs with interrupts enabled, firmware can generate an interrupt by writing the appropriate value to the
P0.2, P0.3 and P0.4 data bits in the P0 Data Register.
Regardless of whether the pins are used as Interrupt or GPIO pins the Int Enable, Int act Low, TTL Threshold, Open Drain, and
Pull-up Enable bits control the behavior of the pin.
The P0.2/INT0–P0.4/INT2 pins are individually configured with the P02CR (0x07), P03CR (0x08), and P04CR (0x09) respec-
tively.
Note Changing the state of the Int Act Low bit can cause an unintentional interrupt to be generated. When configuring these
interrupt sources, it is best to follow the following procedure:
These registers control the operation of pins P0.5 through P0.6, respectively. These registers exist in all enCoRe II parts.
P0.5 and P0.6 are shared with TIO0 and TIO1, respectively. To use these pins as Capture Timer inputs, configure them as inputs
by clearing the corresponding Output Enable. To use TIO0 and TIO1 as Timer outputs, set the TIOx Output and Output Enable
bits. If these pins are configured as outputs and the TIO Output bit is clear, firmware can control the TIO0 and TIO1 inputs by
writing the value to the P0.5 and P0.6 data bits in the P0 Data Register.
Regardless of whether either pin is used as a TIO or GPIO pin the Int Enable, Int act Low, TTL Threshold, Open Drain, and
Pull-up Enable control the behavior of the pin.
TIO0(P0.5) when enabled outputs a positive pulse from the Free Running Timer. This is the same signal that is used internally
to generate the 1024 μs timer interrupt. This signal is not gated by the interrupt enable state. The pulse is active for one cycle
of the capture timer clock.
TIO1(P0.6) when enabled outputs a positive pulse from the programmable interval timer. This is the same signal that is used
internally to generate the programmable timer interval interrupt. This signal is not gated by the interrupt enable state. The pulse
is active for one cycle of the interval timer clock.
The P0.5/TIO0 and P0.6/TIO1 pins are individually configured with the P05CR (0x0A) and P06CR (0x0B), respectively.
1. Disable interrupt source
2. Configure interrupt source
3. Clear any pending interrupts from the source
4. Enable interrupt source
Read/Write
Read/Write
Default
Default
Field
Field
Bit #
Bit #
TIO Output
7
–
0
7
–
0
Reserved
Int Enable
R/W
6
–
0
6
0
Int Act Low
Int Act Low
R/W
R/W
5
0
5
0
TTL Thresh
TTL Thresh
R/W
R/W
4
0
4
0
Reserved
Reserved
(Table 17-7 on page 56
3
–
0
3
–
0
Open Drain
Open Drain
R/W
R/W
CY7C63310, CY7C638xx
2
0
2
0
and
Pull-up Enable
Pull-up Enable
Table 17-5 on page
R/W
R/W
1
0
1
0
Output Enable
Output Enable
Page 38 of 86
R/W
R/W
0
0
0
0
54).
[+] Feedback