CY7C67300-100AXI Cypress Semiconductor Corp, CY7C67300-100AXI Datasheet - Page 39

• Manufacturer Part Number: CY7C67300-100AXI
• Description: IC USB HOST/PERIPH CNTRL 100LQFP
• Manufacturer: Cypress Semiconductor Corp
• Series: EZ-Host™r
• Type: Host Programmable Embedded USBr

Specifications of CY7C67300-100AXI

• Package / Case: 100-LQFP
• Applications: USB Host/Peripheral Controller
• Core Processor: CY16
• Program Memory Type: ROM (8 kB)
• Controller Series: CY7C673xx
• Ram Size: 16K x 8
• Interface: SPI Serial, USB, HPI
• Number Of I /o: 32
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Temperature Range: - 40 C to + 85 C
• Supply Current: 80 mA
• Operating Supply Voltage: 3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: CY4640 - KIT MASS STORAGE REF DESIGNCY3663 - KIT DEV EZ-OTG/EZ-HOST
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 428-1865; CY7C67300-100AXI

Sequence Select (Bit 6)
The Sequence Select bit determines whether a DATA0 or a
DATA1 is sent for the next data toggle. This bit has no effect on
receiving data packets; sequence checking must be handled in
firmware.
1: Send a DATA1
0: Send a DATA0
Stall Enable (Bit 5)
The Stall Enable bit sends a Stall in response to the next request
(unless it is a setup request, which are always ACKed). This is a
sticky bit and continues to respond with Stalls until cleared by
firmware.
1: Send Stall
0: Do not send Stall
ISO Enable (Bit 4)
The ISO Enable bit enables and disables an isochronous trans-
action. This bit is only valid for EPs 1–7 and has no function for
EP0.
1: Enable isochronous transaction
0: Disable isochronous transaction
NAK Interrupt Enable (Bit 3)
The NAK Interrupt Enable bit enables and disables the gener-
ation of an Endpoint n interrupt when the device responds to the
host with a NAK. The Endpoint n Interrupt Enable bit in the
Device n Interrupt Enable register must also be set. When a NAK
is sent to the host, the corresponding EP Interrupt Flag in the
Device n Status register is set. In addition, the NAK Flag in the
Device n Endpoint n Status register is set.
1: Enable NAK interrupt
0: Disable NAK interrupt
Device n Endpoint n Address Register [R/W]
■
■
■
■
■
■
■
■
Table 64. Device n Endpoint n Address Register
Document #: 38-08015 Rev. *J
Bit #
Field
Read/Write
Default
Bit #
Field
Read/Write
Default
Device n Endpoint 0 Address Register [Device 1: 0x0202 Device 2: 0x0282]
Device n Endpoint 1 Address Register [Device 1: 0x0212 Device 2: 0x0292]
Device n Endpoint 2 Address Register [Device 1: 0x0222 Device 2: 0x02A2]
Device n Endpoint 3 Address Register [Device 1: 0x0232 Device 2: 0x02B2]
Device n Endpoint 4 Address Register [Device 1: 0x0242 Device 2: 0x02C2]
Device n Endpoint 5 Address Register [Device 1: 0x0252 Device 2: 0x02D2]
Device n Endpoint 6 Address Register [Device 1: 0x0262 Device 2: 0x02E2]
Device n Endpoint 7 Address Register [Device 1: 0x0272 Device 2: 0x02F2]
R/W
R/W
15
X
X
7
R/W
R/W
14
X
X
6
R/W
R/W
13
X
X
5
R/W
R/W
12
X
X
4
Address...
...Address
Direction Select (Bit 2)
The Direction Select bit needs to be set according to the
expected direction of the next data stage in the next transaction.
If the data stage direction is different from what is set in this bit,
it gets NAKed and either the IN Exception Flag or the OUT
Exception Flag is set in the Device n Endpoint n Status register.
If a setup packet is received and the Direction Select bit is set
incorrectly, the setup is ACKed and the Setup Status Flag is set
(refer to the setup bit of the
[R/W] on page 41
1: OUT transfer (host to device)
0: IN transfer (device to host)
Enable (Bit 1)
Set the Enable bit to allow transfers to the endpoint. If Enable is
set to ‘0’ then all USB traffic to this endpoint is ignored. If Enable
is set ‘1’ and Arm Enable (bit 0) is set ‘0’ then NAKs are automat-
ically returned from this endpoint (except setup packets which
are always ACKed as long as the Enable bit is set).
1: Enable transfers to an endpoint
0: Do not allow transfers to an endpoint
Arm Enable (Bit 0)
The Arm Enable bit arms the endpoint to transfer or receive a
packet. This bit is cleared to ‘0’ when a transaction is complete.
1: Arm endpoint
0: Endpoint disarmed
Reserved
Write all reserved bits with ’0’.
R/W
R/W
11
X
X
3
for details).
R/W
R/W
10
X
X
2
Device n Endpoint n Status Register
R/W
R/W
X
X
1
9
CY7C67300
Page 39 of 99
R/W
R/W
X
X
0
8
[+] Feedback