PIC18F64J11T-I/PT Microchip Technology, PIC18F64J11T-I/PT Datasheet - Page 267

• Manufacturer Part Number: PIC18F64J11T-I/PT
• Description: 16KB, Flash, 1024bytes-RAM, 51I/O, 8-bit Family,nanoWatt 64 TQFP 10x10x1mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F64J11T-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180018 - MODULE PLUG-IN 18F85J11AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PIC18F64J11T-I/PTTR

 2010 Microchip Technology Inc.
20.7
The A/D Converter in the PIC18F85J11 family of
devices includes a self-calibration feature which com-
pensates for any offset generated within the module.
The calibration process is automated and is initiated by
setting the ADCAL bit (ADCON0<7>). The next time
the GO/DONE bit is set, the module will perform a
“dummy” conversion (that is, with reading none of the
input channels) and store the resulting value internally
to compensate for offset. Thus, subsequent offsets will
be compensated.
The calibration process assumes that the device is in a
relatively steady-state operating condition. If A/D
calibration is used, it should be performed after each
device Reset or if there are other major changes in
operating conditions.
20.8
The selection of the automatic acquisition time and A/D
conversion clock is determined in part by the clock
source and frequency while in a power-managed
mode.
TABLE 20-2:
INTCON
PIR1
PIE1
IPR1
PIR3
PIE3
IPR3
ADRESH
ADRESL
ADCON0
ADCON1
ADCON2
CCP2CON
PORTA
TRISA
PORTF
TRISF
Legend:
Note 1:
Name
A/D Converter Calibration
Operation in Power-Managed
Modes
RA6/RA7 and their associated latch and direction bits are configured as port pins only when the internal
oscillator is selected as the default clock source (FOSC2 Configuration bit = 0); otherwise, they are
disabled and these bits read as ‘0’.
— = unimplemented, read as ‘0’. Shaded cells are not used for A/D conversion.
GIE/GIEH PEIE/GIEL TMR0IE
TRISA7
A/D Result Register High Byte
A/D Result Register Low Byte
ADCAL
TRISF5
PSPIE
PSPIP
RA7
PSPIF
ADFM
Bit 7
SUMMARY OF A/D REGISTERS
RF7
—
—
—
—
—
(1)
(1)
TRISA6
TRISF4
RA6
ADIF
ADIE
ADIP
Bit 6
RF6
—
—
—
—
—
—
—
(1)
(1)
TRISA5
TRISF5
VCFG1
ACQT2
DC2B1
RC1IF
RC1IE
RC1IP
RC2IF
RC2IE
RC2IP
CHS3
Bit 5
RA5
RF5
TRISA4
TRISF4
VCFG0
ACQT1
DC2B0
INT0IE
TX1IF
TX1IE
TX1IP
TX2IF
TX2IE
TX2IP
CHS2
Bit 4
RA4
RF4
PIC18F85J11 FAMILY
CCP2M3
TRISA3
TRISF3
If the A/D is expected to operate while the device is in
a power-managed mode, the ACQT<2:0> and
ADCS<2:0> bits in ADCON2 should be updated in
accordance with the power-managed mode clock that
will be used. After the power-managed mode is entered
(either of the power-managed Run modes), an A/D
acquisition or conversion may be started. Once an
acquisition or conversion is started, the device should
continue to be clocked by the same power-managed
mode clock source until the conversion has been
completed. If desired, the device may be placed into
the corresponding power-managed Idle mode during
the conversion.
If the power-managed mode clock frequency is less
than 1 MHz, the A/D RC clock source should be
selected.
Operation in the Sleep mode requires the A/D RC clock
to be selected. If bits, ACQT<2:0>, are set to ‘000’ and
a conversion is started, the conversion will be delayed
one instruction cycle to allow execution of the SLEEP
instruction and entry to Sleep mode. The IDLEN and
SCS<1:0> bits in the OSCCON register must have
already been cleared prior to starting the conversion.
PCFG3
ACQT0
SSPIF
SSPIE
SSPIP
CHS1
RBIE
Bit 3
RA3
RF3
—
—
—
CCP2M2
TMR0IF
CCP2IF
CCP2IE
CCP2IP
TRISA2
PCFG2
TRISF2
ADCS2
CHS0
Bit 2
RA2
RF2
—
—
—
GO/DONE
CCP2M1
TMR2IF
TMR2IE
TMR2IP
CCP1IE
CCP1IP
CCP1IF
TRISA1
TRISF1
PCFG1
ADCS1
INT0IF
Bit 1
RA1
RF1
DS39774D-page 267
CCP2M0
TMR1IF
TMR1IE
TMR1IP
TRISA0
PCFG0
ADCS0
ADON
RBIF
Bit 0
RA0
—
—
—
—
—
on page
Values
Reset
57
59
59
59
59
59
59
59
59
59
59
59
60
60
60
60
60