PIC18F64J11T-I/PT Microchip Technology, PIC18F64J11T-I/PT Datasheet - Page 258

• Manufacturer Part Number: PIC18F64J11T-I/PT
• Description: 16KB, Flash, 1024bytes-RAM, 51I/O, 8-bit Family,nanoWatt 64 TQFP 10x10x1mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F64J11T-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180018 - MODULE PLUG-IN 18F85J11AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PIC18F64J11T-I/PTTR

PIC18F85J11 FAMILY
19.5.2
The operation of the Synchronous Master and Slave
modes is identical except in the case of Sleep or any
Idle mode, and bit, SREN, which is a “don’t care” in
Slave mode.
If receive is enabled by setting the CREN bit prior to
entering Sleep or any Idle mode, then a word may be
received while in this low-power mode. Once the word
is received, the RSR register will transfer the data to the
RCREG2 register. If the RC2IE enable bit is set, the
interrupt generated will wake the chip from the
low-power mode. If the global interrupt is enabled, the
program will branch to the interrupt vector.
TABLE 19-9:
DS39774D-page 258
INTCON
PIR3
PIE3
IPR3
RCSTA2
RCREG2
TXSTA2
SPBRG2
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
Name
AUSART SYNCHRONOUS
SLAVE RECEPTION
AUSART Receive Register
AUSART Baud Rate Generator Register
GIE/GIEH PEIE/GIEL TMR0IE
CSRC
SPEN
Bit 7
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
—
—
—
Bit 6
RX9
TX9
—
—
—
RC2IE
RC2IP
RC2IF
SREN
TXEN
Bit 5
INT0IE
CREN
TX2IF
TX2IE
TX2IP
SYNC
Bit 4
ADDEN
To set up a Synchronous Slave Reception:
1.
2.
3.
4.
5.
6.
7.
8.
9.
RBIE
Bit 3
—
—
—
—
Enable the synchronous master serial port by
setting bits, SYNC and SPEN, and clearing bit,
CSRC.
If interrupts are desired, set enable bit, RC2IE.
If 9-bit reception is desired, set bit, RX9.
To enable reception, set enable bit, CREN.
Flag bit, RC2IF, will be set when reception is
complete. An interrupt will be generated if
enable bit, RC2IE, was set.
Read the RCSTA2 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG2 register.
If any error occurred, clear the error by clearing
bit, CREN.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
TMR0IF
CCP2IE
CCP2IP
CCP2IF
BRGH
FERR
Bit 2
CCP1IE
CCP1IP
CCP1IF
INT0IF
OERR
TRMT
 2010 Microchip Technology Inc.
Bit 1
RX9D
TX9D
RBIF
Bit 0
—
—
—
on page
Values
Reset
57
59
59
59
61
61
61
61