PIC18F64J11T-I/PT Microchip Technology, PIC18F64J11T-I/PT Datasheet - Page 137

• Manufacturer Part Number: PIC18F64J11T-I/PT
• Description: 16KB, Flash, 1024bytes-RAM, 51I/O, 8-bit Family,nanoWatt 64 TQFP 10x10x1mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F64J11T-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180018 - MODULE PLUG-IN 18F85J11AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PIC18F64J11T-I/PTTR

11.5
PORTD is an 8-bit wide, bidirectional port. The corre-
sponding Data Direction and Output Latch registers are
TRISD and LATD. All pins on PORTD are digital only
and tolerate voltages up to 5.5V.
All pins on PORTD are implemented with Schmitt
Trigger input buffers. Each pin is individually
configurable as an input or output.
Each of the PORTD pins has a weak internal pull-up. A
single control bit can turn off all the pull-ups. This is
performed by clearing bit, RDPU (PORTG<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on all device Resets.
On 80-pin devices, PORTD is multiplexed with the
system bus as part of the external memory interface.
I/O port and other functions are only available when the
interface is disabled, by setting the EBDIS bit
(MEMCON<7>). When the interface is enabled,
PORTD is the low-order byte of the multiplexed
address/data bus (AD<7:0>). The TRISD bits are also
overridden.
 2010 Microchip Technology Inc.
Note:
PORTD, TRISD and
LATD Registers
These pins are configured as digital inputs
on any device Reset.
PIC18F85J11 FAMILY
PORTD can also be configured to function as an 8-bit
wide, parallel microprocessor port by setting the
PSPMODE control bit (PSPCON<4>). In this mode,
parallel port data takes priority over other digital I/O (but
not the external memory interface). When the parallel
port is active, the input buffers are TTL. For more
information, refer to Section 11.11 “Parallel Slave
Port”.
EXAMPLE 11-4:
CLRF
CLRF
MOVLW
MOVWF
PORTD
LATD
0CFh
TRISD
; Initialize PORTD by
; clearing output
; data latches
; Alternate method
; to clear output
; data latches
; Value used to
; initialize data
; direction
; Set RD<3:0> as inputs
; RD<5:4> as outputs
; RD<7:6> as inputs
INITIALIZING PORTD
DS39774D-page 137