MCP4728T-E/UN Microchip Technology, MCP4728T-E/UN Datasheet - Page 36

• Manufacturer Part Number: MCP4728T-E/UN
• Description: Quad, 12-bit NV DAC With I2C Interface 10 MSOP 3x3mm T/R
• Manufacturer: Microchip Technology

Specifications of MCP4728T-E/UN

• Settling Time: 6µs
• Number Of Bits: 12
• Data Interface: I²C
• Number Of Converters: 4
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP4728EV - BOARD EVAL 12BIT 4CH DAC MCP4728
• Power Dissipation (max): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MCP4728
5.6.3
When the device receives this command, it writes the
input data to the DAC input registers sequentially from
the starting channel to channel D, and also writes to
EEPROM sequentially. The starting channel is
determined by the DAC1 and DAC0 bits.
shows the functions of the channel selection bits for the
sequential write command.
When the device is writing EEPROM, the RDY/BSY bit
stays “Low” until the EEPROM write operation is
completed. The state of the RDY/BSY bit flag can be
monitored by a read command or at the RDY/BSY pin.
Any new command received during the EEPROM write
operation (RDY/BSY bit is “Low”) is ignored.
shows an example of the sequential write command.
Updating Analog Outputs:
The analog outputs can be updated by one of the
following events after the falling edge of the
acknowledge clock pulse of the 4th byte.
a.
b.
c.
TABLE 5-2:
DS22187E-page 36
Note:
DAC1
When the LDAC pin or UDAC bit is “Low”.
If UDAC bit is “High”, bringing down the LDAC
pin to “Low” any time.
By sending the General Call Software Update
command.
0
0
1
1
SEQUENTIAL WRITE COMMAND:
WRITE DAC INPUT REGISTERS
AND EEPROM SEQUENTIALLY
FROM STARTING CHANNEL TO
CHANNEL D
(C2=0, C1=1, C0=0; W1=1, W0=0)
The UDAC bit can be used effectively to
upload the input register to the output
register, but it affects only a selected
channel only, while the LDAC pin and
General Call Software Update command
affect all channels.
DAC0
0
1
0
1
DAC CHANNEL SELECTION
BITS FOR SEQUENTIAL
WRITE COMMAND
Ch. A - Ch. D
Ch. B - Ch. D
Ch. C - Ch. D
Channels
Ch. D
Figure 5-9
Table 5-2
5.6.4
When the device receives this command, it writes the
input data to a selected single DAC input register and
also to its EEPROM. The channel is selected by the
channel selection bits (DAC1 and DAC0). See
Table 5-2
Figure 5-10
command.
Updating Analog Outputs:
The analog outputs can be updated by one of the
following events after the falling edge of the
acknowledge clock pulse of the 4th byte.
a.
b.
c.
Note:
When the LDAC pin or UDAC bit is “Low”.
If UDAC bit is “High”, bringing down the LDAC
pin to “Low” any time.
By sending the General Call Software Update
command.
for the channel selection bit function.
SINGLE WRITE COMMAND: WRITE
A SINGLE DAC INPUT REGISTER
AND EEPROM
(C2=0, C1=1, C0=0; W1=1, W0=1)
The UDAC bit can be used effectively to
upload the input register to the output
register, but it affects only a selected
channel only, while the LDAC pin and
General Call Software Update command
affect all channels.
shows an example of the single write
© 2010 Microchip Technology Inc.