C8051F340-GQR Silicon Laboratories Inc, C8051F340-GQR Datasheet - Page 264

• Manufacturer Part Number: C8051F340-GQR
• Description: MCU 8-Bit C8051F34x 8051 CISC 64KB Flash 3.3V/5V 48-Pin TQFP T/R
• Manufacturer: Silicon Laboratories Inc

Specifications of C8051F340-GQR

• Package: 48TQFP
• Device Core: 8051
• Family Name: C8051F34x
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 40
• Interface Type: I2C/SMBus/SPI/UART/USB
• On-chip Adc: 17-chx10-bit
• Number Of Timers: 4
• Ram Size: 4.25 KB
• Program Memory Size: 64 KB
• Program Memory Type: Flash
• Operating Temperature: -40 to 85 °C

C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
22.3. Watchdog Timer Mode
A programmable watchdog timer (WDT) function is available through the PCA Module 4. The WDT is used
to generate a reset if the time between writes to the WDT update register (PCA0CPH4) exceed a specified
limit. The WDT can be configured and enabled/disabled as needed by software.
With the WDTE and/or WDLCK bits set to ‘1’ in the PCA0MD register, Module 4 operates as a watchdog
timer (WDT). The Module 4 high byte is compared to the PCA counter high byte; the Module 4 low byte
holds the offset to be used when WDT updates are performed. The Watchdog Timer is enabled on
reset. Writes to some PCA registers are restricted while the Watchdog Timer is enabled.
22.3.1. Watchdog Timer Operation
While the WDT is enabled:
•
•
•
•
•
•
While the WDT is enabled, writes to the CR bit will not change the PCA counter state; the counter will run
until the WDT is disabled. The PCA counter run control (CR) will read zero if the WDT is enabled but user
software has not enabled the PCA counter. If a match occurs between PCA0CPH4 and PCA0H while the
WDT is enabled, a reset will be generated. To prevent a WDT reset, the WDT may be updated with a write
of any value to PCA0CPH4. Upon a PCA0CPH4 write, PCA0H plus the offset held in PCA0CPL4 is loaded
into PCA0CPH4 (See Figure 22.10).
Note that the 8-bit offset held in PCA0CPH4 is compared to the upper byte of the 16-bit PCA counter. This
offset value is the number of PCA0L overflows before a reset. Up to 256 PCA clocks may pass before the
first PCA0L overflow occurs, depending on the value of the PCA0L when the update is performed. The
total offset is then given (in PCA clocks) by Equation 22.4, where PCA0L is the value of the PCA0L register
at the time of the update.
264
PCA counter is forced on.
Writes to PCA0L and PCA0H are not allowed.
PCA clock source bits (CPS2-CPS0) are frozen.
PCA Idle control bit (CIDL) is frozen.
Module 4 is forced into Watchdog Timer mode.
Writes to the Module 4 mode register (PCA0CPM4) are disabled.
PCA0CPL4
C
D
L
I
Figure 22.10. PCA Module 4 with Watchdog Timer Enabled
W
D
T
E
PCA0MD
W
D
C
L
K
PCA0CPH4
C
P
S
2
Write to
C
P
S
1
C
P
S
0
E
C
F
8-bit Adder
Enable
Adder
Enable
Rev. 1.3
PCA0CPH4
Comparator
PCA0H
8-bit
Match
PCA0L Overflow
Reset