C8051F340-GQR Silicon Laboratories Inc, C8051F340-GQR Datasheet - Page 183

• Manufacturer Part Number: C8051F340-GQR
• Description: MCU 8-Bit C8051F34x 8051 CISC 64KB Flash 3.3V/5V 48-Pin TQFP T/R
• Manufacturer: Silicon Laboratories Inc

Specifications of C8051F340-GQR

• Package: 48TQFP
• Device Core: 8051
• Family Name: C8051F34x
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 40
• Interface Type: I2C/SMBus/SPI/UART/USB
• On-chip Adc: 17-chx10-bit
• Number Of Timers: 4
• Ram Size: 4.25 KB
• Program Memory Size: 64 KB
• Program Memory Type: Flash
• Operating Temperature: -40 to 85 °C

16.13. Controlling Endpoints1-3 OUT
Endpoints1-3 OUT are managed via USB registers EOUTCSRL and EOUTCSRH. All OUT endpoints can
be used for Interrupt, Bulk, or Isochronous transfers. Isochronous (ISO) mode is enabled by writing ‘1’ to
the ISO bit in register EOUTCSRH. Bulk and Interrupt transfers are handled identically by hardware.
An Endpoint1-3 OUT interrupt may be generated by the following:
16.13.1.Endpoints1-3 OUT Interrupt or Bulk Mode
When the ISO bit (EOUTCSRH.6) = ‘0’ the target endpoint operates in Bulk or Interrupt mode. Once an
endpoint has been configured to operate in Bulk/Interrupt OUT mode (typically following an Endpoint0
SET_INTERFACE command), hardware will set the OPRDY bit (EOUTCSRL.0) to ‘1’ and generate an
interrupt upon reception of an OUT token and data packet. The number of bytes in the current OUT data
packet (the packet ready to be unloaded from the FIFO) is given in the EOUTCNTH and EOUTCNTL reg-
isters. In response to this interrupt, firmware should unload the data packet from the OUT FIFO and reset
the OPRDY bit to ‘0’.
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bits1–0: Unused. Read = 00b; Write = don’t care.
USB Register Definition 16.20. EINCSRH: USB0 IN Endpoint Control High Byte
DBIEN
R/W
Bit7
1. Hardware sets the OPRDY bit (EINCSRL.0) to ‘1’.
2. Hardware generates a STALL condition.
DBIEN: IN Endpoint Double-buffer Enable.
0: Double-buffering disabled for the selected IN endpoint.
1: Double-buffering enabled for the selected IN endpoint.
ISO: Isochronous Transfer Enable.
This bit enables/disables isochronous transfers on the current endpoint.
0: Endpoint configured for bulk/interrupt transfers.
1: Endpoint configured for isochronous transfers.
DIRSEL: Endpoint Direction Select.
This bit is valid only when the selected FIFO is not split (SPLIT = ‘0’).
0: Endpoint direction selected as OUT.
1: Endpoint direction selected as IN.
Unused. Read = ‘0’. Write = don’t care.
FCDT: Force Data Toggle.
0: Endpoint data toggle switches only when an ACK is received following a data packet
transmission.
1: Endpoint data toggle forced to switch after every data packet is transmitted, regardless of
ACK reception.
SPLIT: FIFO Split Enable.
When SPLIT = ‘1’, the selected endpoint FIFO is split. The upper half of the selected FIFO is
used by the IN endpoint; the lower half of the selected FIFO is used by the OUT endpoint.
ISO
R/W
Bit6
DIRSEL
R/W
Bit5
C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
Bit4
R
-
Rev. 1.3
FCDT
R/W
Bit3
SPLIT
R/W
Bit2
Bit1
R
-
Bit0
R
-
USB Address:
00000000
Reset Value
0x12
183