QB-MINI2-EE NEC, QB-MINI2-EE Datasheet - Page 19
QB-MINI2-EE
Manufacturer Part Number
QB-MINI2-EE
Description
EMULATOR, PROGRAMMER, MINICUBE2
Manufacturer
NEC
Type
Debug Emulatorr
Datasheet
1.QB-MINI2-EE.pdf
(169 pages)
Specifications of QB-MINI2-EE
Svhc
No SVHC (18-Jun-2010)
Mcu Supported Families
MINICUBE2
Silicon Family Name
V850, 78K0R, 78K0S
Ic Product Type
On-Chip Debug Emulator
Kit Contents
MINICUBE2, USB Cable, Target Cable, 78K0-OCD Board
Features
On-Chip Debugging, Flash Memory Programming,
- Current page: 19 of 169
- Download datasheet (6Mb)
3.1.1 Pin assignment
Note Signal names in MINICUBE2
Note As seen from MINICUBE2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
RESET_IN
RESET_OUT
CLK
FLMD0
FLMD1
RxD/SI
TxD/SO
SCK
H/S
R.F.U.
the pin assignment. Table 3-2 describes the functions of each pin. The pin assignment varies depending on
whether CSI-H/S or UART is used, so design the circuit appropriately according to the circuit connection examples
described on the following sections.
Pin No.
Pin Name
This section describes the interface signals used between MINICUBE2 and the target system. Table 3-1 lists
GND
RESET_OUT
SI
VDD
SO
R.F.U.
SCK
H/S
CLK
R.F.U.
R.F.U.
FLMD1
R.F.U.
FLMD0
RESET_IN
R.F.U.
CSI-H/S Used
IN
OUT
OUT
OUT
OUT
IN
OUT
OUT
IN
-
CHAPTER 3
IN/OUT
Pin Name
Note
R.F.U.
R.F.U.
RXD
TXD
Pin used to input reset signal from the target system
Pin used to output reset signal to the target device
Pin used to output clock signal to the target device
programming mode
Pin used to receive command/data from the target device
Pin used to output clock signal for 3-wire serial communication
Pin used to input handshake signal from the target device
This pin is not used, so leave it open.
Note
Pin used to set the target device to debug mode or
Pin used to set programming mode
Pin used to transmit command/data to the target device
HOW TO USE MINICUBE2 WITH V850 MICROCONTROLLER
UART Used
Table 3-1. Pin Assignment
User’s Manual U18371EJ1V0UM
Table 3-2. Pin Functions
15
15
16
16
Description
Pin assignment of target connector
Pin assignment of target connector
to be mounted on target system
to be mounted on target system
13
13
14
14
11
11
12
12
TOP VIEW
TOP VIEW
10
10
9
9
Target system
Target system
7
7
8
8
5
5
6
6
Pin 1
Pin 1
3
3
4
4
1
1
2
2
19
Related parts for QB-MINI2-EE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: