CJ1W-NC414 Omron, CJ1W-NC414 Datasheet - Page 516
CJ1W-NC414
Manufacturer Part Number
CJ1W-NC414
Description
High Speed Pulse Train 4 Axes
Manufacturer
Omron
Datasheet
1.CJ1W-NC214.pdf
(601 pages)
Specifications of CJ1W-NC414
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 516 of 601
- Download datasheet (14Mb)
12
12-1 Troubleshooting
12-7
No.
46
47
48
49
50
51
52
53
54
55
56
57
58
59
Motor shaft
shakes.
Position shift
Problem
Insufficient adjustment
of the gain (low gain)
Gain cannot be
adjusted due to low
machine rigidity.
Mechanical
configuration prone to
stick slip (highly sticky
static friction)
Wrong motor selection
(adjustment not
possible)
Failure
Unstable shift amount
Malfunction due to
noise
The origin position
was already shifted
before positioning.
The shield is not
grounded at a single
point on the Servo
Drive side.
The output power
supply for the PCU is
not isolated from other
power supplies.
Cable between the
PCU and driver is
long.
Twisted-pair cable is
not used for pulse
output.
Cable between the
PCU and driver not
isolated from other
power lines.
Probable cause
CJ Position Control Units OPERATION MANUAL (CJ1W-NC214/234/414/434)
(In particular, this
condition occurs on
vertical axes, SCARA
robots, palletizers and
other systems whose
axis receives bending or
tensional loads.)
Select an appropriate
motor (check the torque
and inertia ratio).
Refer to No. 25 and 26.
Check the ground
wiring.
Check if the output
power supply for the
PCU is isolated from
other power supplies.
Check if a twisted-pair
cable is used for pulse
output.
Check if the cable
between the PCU and
driver is isolated from
other power lines.
Item to check
−
−
−
−
−
Perform auto-tuning.
Manually adjust (raise)
the gain.
Increase the machine
rigidity.
Readjust the gain.
Perform auto-tuning.
Manually adjust the
gain.
Change to an optimal
motor.
Replace the driver.
Replace the motor.
Use a shielded cable.
Refer to No. 25 and 26.
Wire correctly.
Isolate the output power
supply for the PCU from
other power supplies.
Provide a noise filter on
the primary side of the
output power supply for
the PCU.
Ground the output
power supply for the
PCU.
Keep the cable within 3
m for the open-collector
output type and within
10 m for the line-driver
output type.
Use a twisted-pair cable
for pulse output.
Isolate the cable
between the PCU and
driver from other power
lines.
Countermeasure
Confirm
Related parts for CJ1W-NC414
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ANALOG IN, CJ1, 4CH, HIGH SPPE
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
High Speed Pulse Train 2 Axes
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
High Speed Pulse Train 2 Axes
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
High Speed Pulse Train 4 Axes
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CJ Profinet Master
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Ethernet I/P Module
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
HIGH SPEED COUNTER 500Khz 2 CH
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Isolated Universal Analog 4pt
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CJ1 CompoNet Master
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: