FX1S-30MR-ES/UL MITSUBISHI, FX1S-30MR-ES/UL Datasheet - Page 226

• Manufacturer Part Number: FX1S-30MR-ES/UL
• Description: PLC, 16 IN, 14 RELAY OUT, 110V/2
• Manufacturer: MITSUBISHI

Specifications of FX1S-30MR-ES/UL

• No. Of Analogue Inputs: 16
• No. Of Analogue Outputs: 14
• Ip/nema Rating: IP10
• Approval Bodies: CE, CUL, UL
• External Depth: 49mm
• External Length / Height: 90mm
• External Width: 60mm
• Mounting Type: Panel

FX Series Programmable Controlers
PID setup parameters; S
The PID setup parameters are contained in a 25 register data stack. Some of these devices
require data input from the user, some are reserved for the internal operation and some return
output data from the PID operation.
Parameters S
See Initial values for PID loops for basic guidance on initial PID values; page 5-114.
See page 10-24 for additional parameters available with FX
Parame-
S
S3 + P
S
S
S
S
S
S
S
S
S
S
S
S
S
3
3
3
3
3
3
3
ter
+7 to
3
3
3
3
3
3
3
+19
+20
+21
+22
+23
+24
+0
+1
+2
+3
+4
+5
+6
Output Value,
maximum
negative change
Action - reaction
positive change
positive change
name/function
Process Value,
Process Value,
minimum value
Derivative time
Sampling time
Output Value,
alarm control
direction and
Integral time
Input filter
Proportional
(Read Only)
constant T
Alarm flags
Parameter
constant T
3
Derivative
maximum
maximum
+0 through S
gain K
gain K
T
S
P
D
D
I
3
The time interval set between the reading the current
Process Value of the system (PV
b0
b1
b2
b3 - 15
Alters the effect of the input filter.
This is a factor used to align the proportional output in a
known magnitude to the change in the Process Value
(PV
This is the I part of the PID loop.
This is the time taken for the corrective integral value to
reach a magnitude equal to that applied by the
proportional or P part of the loop.
Selecting 0 (zero) for this parameter disables the I effect.
This is a factor used to align the derivative output in a
known proportion to the change in the Process Value
(PV
This is the D part of the PID loop.
This is the time taken for the corrective derivative value to
reach a magnitude equal to that applied by the
proportional or P part of the loop.
Selecting 0 (zero) for this parameter disables the D effect.
Active
when
S
b1 is
set ON.
Active
when
S
b2 is
set ON.
b0
b1
b2
b3
b4 - 15
3
3
3
+6 must be set by the user.
+1,
+1,
nf
nf
). This is the P part of the PID loop.
)
Reserved for use for the internal processing
Forward operation(0),
Reverse operation (1)
Process Value (PV
ON(1)
Output Value (MV) alarm enable, OFF(0)/ON(1)
Reserved
This is a user defined maximum limit for the
Process Value (PV
(PV
This is a user defined lower limit for the Process
Value. If the Process Value (PV
the limit, S
This is a user defined maximum limit for the
quantity of positive change which can occur in
one PID scan. If the Output Value (MV) exceeds
this, S
This is a user defined maximum limit for the
quantity of negative change which can occur in
one PID scan. If the Output Value (MV) falls
below the lower limit, S
High limit exceeded in Process Value (PV
Below low limit for the Process Value (PV
Excessive positive change in Output Value (MV)
Excessive negative change in Output Value
(MV)
Reserved
nf
) exceeds the limit, S
3
+24, bit b2 is set On.
3
+24, bit b1 is set On.
Description
nf
nf
) alarm enable, OFF(0)/
). If the Process Value
3
nf
+24, bit b3 is set On.
)
2N,
3
+24, bit b0 is set On.
FX
2NC
nf
) falls below
& FX
Applied Instructions 5
1N
nf
nf
)
)
MPUs.
5-104
(0 to 32767)
(0 to 32767)
x 100 msec
1 to 32767
0 to 32767
applicable
1 to 100%
x 10 msec
applicable
0 to 99%
32767%
Setting
range
msec
1 to
Not
Not