SI1015-A-GM Silicon Laboratories Inc, SI1015-A-GM Datasheet - Page 349

• Manufacturer Part Number: SI1015-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1015-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 0.9 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1868-5

27.2.2. 8-Bit Timers with Auto-Reload
When T2SPLIT is set, Timer 2 operates as two 8-bit timers (TMR2H and TMR2L). Both 8-bit timers oper-
ate in auto-reload mode as shown in Figure 27.5. TMR2RLL holds the reload value for TMR2L; TMR2RLH
holds the reload value for TMR2H. The TR2 bit in TMR2CN handles the run control for TMR2H. TMR2L is
always running when configured for 8-bit Mode.
Each 8-bit timer may be configured to use SYSCLK, SYSCLK divided by 12, SmaRTClock divided by 8 or
Comparator 0 output. The Timer 2 Clock Select bits (T2MH and T2ML in CKCON) select either SYSCLK or
the clock defined by the Timer 2 External Clock Select bits (T2XCLK[1:0] in TMR2CN), as follows:
The TF2H bit is set when TMR2H overflows from 0xFF to 0x00; the TF2L bit is set when TMR2L overflows
from 0xFF to 0x00. When Timer 2 interrupts are enabled (IE.5), an interrupt is generated each time
TMR2H overflows. If Timer 2 interrupts are enabled and TF2LEN (TMR2CN.5) is set, an interrupt is gener-
ated each time either TMR2L or TMR2H overflows. When TF2LEN is enabled, software must check the
TF2H and TF2L flags to determine the source of the Timer 2 interrupt. The TF2H and TF2L interrupt flags
are not cleared by hardware and must be manually cleared by software.
T2MH
0
0
0
0
1
SmaRTClock / 8
Comparator 0
SYSCLK / 12
T2XCLK[1:0] TMR2H Clock
00
01
10
11
X
T2XCLK[1:0]
00
01
11
Figure 27.5. Timer 2 8-Bit Mode Block Diagram
Source
SYSCLK / 12
SmaRTClock / 8
Reserved
Comparator 0
SYSCLK
SYSCLK
0
1
1
0
M
H
T
3
M
T
3
L
CKCON
M
T
2
H
M
T
2
L
M
T
1
M
T
0
TR2
S
C
A
1
C
S
A
0
Rev. 1.0
TCLK
TCLK
T2ML
0
0
0
0
1
TMR2RLH
TMR2RLL
TMR2H
TMR2L
Reload
Reload
T2XCLK[1:0] TMR2L Clock
10
X
00
01
11
Si1010/1/2/3/4/5
To SMBus
To ADC,
TF2CEN
T2SPLIT
SMBus
TF2LEN
T2XCLK
TF2H
TF2L
TR2
Source
SYSCLK / 12
SmaRTClock / 8
Reserved
Comparator 0
SYSCLK
Interrupt
349