SI1015-A-GM Silicon Laboratories Inc, SI1015-A-GM Datasheet - Page 29

• Manufacturer Part Number: SI1015-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1015-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 0.9 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1868-5

1.7. Programmable Current Reference (IREF0)
Si1010/1/2/3/4/5 devices include an on-chip programmable current reference (source or sink) with two out-
put current settings: low power mode and high current mode. The maximum current output in low power
mode is 63 µA (1 µA steps) and the maximum current output in high current mode is 504 µA (8 µA steps).
1.8. Comparators
Si1010/1/2/3/4/5 devices include two on-chip programmable voltage comparators: Comparator 0 (CPT0)
which is shown in Figure 1.13; Comparator 1 (CPT1) which is shown in Figure 1.14. The two comparators
operate identically but may differ in their ability to be used as reset or wake-up sources. See Section
“18. Reset Sources” on page 185 and the Section “14. Power Management” on page 157 for details on
reset sources and low power mode wake-up sources, respectively.
The Comparator offers programmable response time and hysteresis, an analog input multiplexer, and two
outputs that are optionally available at the Port pins: a synchronous “latched” output (CP0, CP1), or an
asynchronous “raw” output (CP0A, CP1A). The asynchronous CP0A signal is available even when the
system clock is not active. This allows the Comparator to operate and generate an output when the device
is in some low power modes.
The comparator inputs may be connected to Port I/O pins or to other internal signals. Port pins may also be
used to directly sense capacitive touch switches. See Application Note AN338 for details on Capacitive
Touch Switch sensing.
Sensor
Temp
VDD_MCU/DC+
Digital Supply
P1.6*
P0.0
VBAT
Figure 1.12. ADC0 Multiplexer Block Diagram
available as device pins
*P1.0 – P1.3 are not
ADC0MX
AMUX
Rev. 1.0
Gain = 0. 5 or 1
Programmable
Attenuator
Si1010/1/2/3/4/5
AIN+
ADC0
29