SPBT2532C2.AT STMicroelectronics, SPBT2532C2.AT Datasheet - Page 31
![IC BLUETOOTH VER 2.1 CLASS 2](/photos/14/20/142004/spbt2532c2_at_sml.jpg)
SPBT2532C2.AT
Manufacturer Part Number
SPBT2532C2.AT
Description
IC BLUETOOTH VER 2.1 CLASS 2
Manufacturer
STMicroelectronics
Datasheets
1.STEVAL-SPBT2ATV1.pdf
(50 pages)
2.SPBT2532C2.AT.pdf
(2 pages)
3.SPBT2532C2.AT.pdf
(55 pages)
Specifications of SPBT2532C2.AT
Frequency
2.4GHz
Data Rate - Maximum
2Mbps
Modulation Or Protocol
Bluetooth v2.1+EDR, Class 2 & 3
Applications
General Purpose
Power - Output
2dBm
Sensitivity
-85dBm
Voltage - Supply
2.8 V ~ 3.6 V
Data Interface
PCB, Surface Mount
Memory Size
256kB Flash, 48kB RAM
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Wireless Frequency
2400 MHz to 2483.5 MHz
Interface Type
I2C, I2S, SPI, UART
Data Rate
2 Mbps
Modulation
AFH
Operating Voltage
2.8 V to 3.6 V
Antenna
Without Antenna
Board Size
10 mm x 13 mm
Operating Temperature Range
- 40 C to + 85 C
Output Power
4 mA
Security
128 bit Encryption
Technology/ Type
Class 2 Bluetooth Module
Processor Series
STLC2500
For Use With
497-10656 - BOARD DEMO BLUETOOTH SPBT2532C2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Transmitting
-
Current - Receiving
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
Bluetooth Devices
Other names
497-10539
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SPBT2532C2.AT2
Manufacturer:
Broadchip
Quantity:
16 000
SPBT2532C2.AT
D.9
D.9.1
D.9.2
D.10
D.10.1
D.10.2
D.11
D.11.1
D.11.2
DeleteSmartCable
The DeleteSmartCable command removes the current Smart Cable settings that were
entered using the SmartCableSetup command, but not the setting from the dynamic
configuration. The Smart Cable will then be deactivated for the remainder of this session.
Upon reset, if a dynamic configuration for a Smart Cable exists, it will be activated. If there is
no dynamic configuration Smart Cable setup, then this feature will remain deactivated.
Syntax
AT+AB DeleteSmartCable
Responses
If the operation is successful, the response is:
AT-AB DeleteSmartCableDone
DisableBond
The DisableBond command is used to disallow new bonding with a device.
This command cannot be used while a connection is active.
Syntax
AT+AB DisableBond
Responses
If the operation is successful, the response is:
AT-AB BondDisabled
Discovery
The Discovery command is used to initiate a device discovery. The command will return the
number of responses of nearby devices and then the individual responses with BD address,
name of device. The number of devices returned is limited to 10.
Inquiry is performed with an interval of 10.24 seconds.
The devices are reported in the same order as the original inquiry results.
Syntax
AT+AB Discovery
Responses
When the discovery command has been accepted, the response is:
AT-AB InqPending
Doc ID 16089 Rev 7
Command description
31/50