ACE1501EN Fairchild Semiconductor, ACE1501EN Datasheet - Page 27

IC MCU 1KBIT EEPROM 8DIP

ACE1501EN

Manufacturer Part Number
ACE1501EN
Description
IC MCU 1KBIT EEPROM 8DIP
Manufacturer
Fairchild Semiconductor
Series
ACEX® 15xxr
Datasheet

Specifications of ACE1501EN

Core Processor
ACE1502
Core Size
8-Bit
Speed
25MHz
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
6
Program Memory Size
1KB (1K x 8)
Program Memory Type
EEPROM
Eeprom Size
64 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
Connectivity
-
ACE1501 Product Family Rev. 1.1
12. RESET block
When a RESET sequence is initiated, all I/O registers will be
reset setting all I/Os to high-impedence inputs. The system
clock is restarted after the required clock start-up delay. A reset
is generated by any one of the following four conditions:
13. Power-On Reset
The Power-On Reset (POR) circuit is guaranteed to work if the
rate of rise of Vcc is no slower than 10ms/1volt. The POR circuit
was designed to respond to fast low to high transitions between
0V and Vcc. The circuit will not work if Vcc does not drop to 0V
before the next power-up sequence. In applications where 1)
the Vcc rise is slower than 10ms/1 volt or 2) Vcc does not drop
14. CLOCK
The ACEx microcontroller has an on-board oscillator trimmed to
a frequency of 2MHz who is divided down by two yielding a
1MHz frequency. (See AC Electrical Characteristics) Upon
power-up, the on-chip oscillator runs continuously unless enter-
ing HALT mode or using an external clock source.
If required, an external oscillator circuit may be used depending
on the states of the CMODE bits of the initialization register.
(See Table 16) When the device is driven using an external
clock, the clock input to the device (G1/CKI) can range between
DC to 4MHz. For external crystal configuration, the output clock
(CKO) is on the G0 pin. (See Figure 34.) If the device is config-
ured for an external square clock, it will not be divided.
Table 16. CMODEx Bit Definition
The HALT mode is a power saving feature that almost com-
pletely shuts down the device for current conservation. The
device is placed into HALT mode by setting the HALT enable bit
(EHALT) of the HALT register through software using only the
“LD M, #” instruction. EHALT is a write only bit and is automati-
cally cleared upon exiting HALT. When entering HALT, the inter-
nal oscillator and all the on-chip systems including the LBD and
the BOR circuits are shut down.
Figure 35. HALT Register Definition
15. HALT Mode
CMODE [1] CMODE [0]
Undefined
Bit 7
0
0
1
1
undefined
Bit 6
0
1
0
1
External crystal/resonator
undefined
External square clock
Internal 1 MHz clock
Bit 5
Clock Type
Reserved
undefined
Bit 4
27
• Power-on Reset (as described in Section 13)
• Brown-out Reset (as described in Section 11.1)
• Watchdog Reset (as described in Section 6)
• External Reset
18. Available only on the 14-pin package option
to 0V before the next power-up sequence the external reset
option should be used.
The external reset provides a way to properly reset the ACEx
microcontroller if POR cannot be used in the application. The
external reset pin contains an internal pull-up resistor. There-
fore, to reset the device the reset pin should be held low for at
least 2ms so that the internal clock has enough time to stabilize.
Figure 34. Crystal
The device can exit HALT mode only by the MIW circuit. There-
fore, prior to entering HALT mode, software must configure the
MIW circuit accordingly. (See Section 8) After a wakeup from
HALT, a 1ms start-up delay is initiated to allow the internal oscil-
lator to stabilize before normal execution resumes. Immediately
after exiting HALT, software must clear the Power Mode Clear
(PMC) register by only using the “LD M, #” instruction. (See Fig-
ure 36)
undefined
Bit 3
undefined
18
Bit 2
(as described in Section 13)
C2
CKI
R2
C1
EIDLE
Bit 1
CKO
R1
www.fairchildsemi.com
EHALT
Bit 0

Related parts for ACE1501EN