PIC17C756-16/SP Microchip Technology, PIC17C756-16/SP Datasheet - Page 246

• Manufacturer Part Number: PIC17C756-16/SP
• Description: MICRO CTRL 16K MEMORY OTP 64SDIP
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17C756-16/SP

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: OTP
• Ram Size: 902 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 64-SDIP (0.750", 19.05mm)
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -
• Other names: PIC17C756-16/P

PIC17C7XX
DS30289B-page 246
DC CHARACTERISTICS
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
Param.
Note 1: When using the Table Write for internal programming, the device temperature must be less than 40°C.
D150
D100
D101
D102
D110
D111
D112
D113
D114
†
No.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. Higher leakage
3: Negative current is defined as current sourced by the pin.
4: These specifications are for the programming of the on-chip program memory EPROM through the use of the
5: The MCLR/V
6: For TTL buffers, the better of the two specifications may be used.
2: For In-Circuit Serial Programming (ICSP ), refer to the device programming specification.
Data in “Typ” column is at 5V, 25 C unless otherwise stated.
PIC17CXXX devices be driven with external clock in RC mode.
current may be measured at different input voltages.
table write instructions. The complete programming specifications can be found in: PIC17C7XX Programming
Specifications (Literature number DS TBD).
V
C
C
C
V
V
I
I
T
PP
DDP
Sym
OD
PROG
PP
DDP
OSC
IO
AD
2 OSC2/CLKOUT pin
Open Drain High Voltage
Capacitive Loading Specs on
Output Pins
All I/O pins and OSC2
(in RC mode)
System Interface Bus
(PORTC, PORTD and PORTE)
Internal Program Memory
Programming Specs (Note 4)
Voltage on MCLR/V
Supply voltage during
programming
Current into MCLR/V
Supply current during
programming
Programming pulse width
PP
pin may be kept in this range at times other than programming, but is not recommended.
Characteristic
PP
PP
pin
pin
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Operating voltage V
12.75
4.75
Min
100
–
–
–
–
–
–
Typ†
5.0
25
–
–
–
–
–
–
–
DD
range as described in Section 20.1
-40°C
-40°C
0°C
13.25
1000
Max
5.25
8.5
25
50
50
50
30
Units
mA
mA
ms
T
T
pF
pF
pF
2000 Microchip Technology Inc.
V
V
V
T
A
A
A
+85°C for industrial
+70°C for commercial
+125°C for extended
RA2 and RA3 pins only
pulled up to externally
applied voltage
In EC or RC osc modes,
when OSC2 pin is outputting
CLKOUT. External clock is
used to drive OSC1.
In Microprocessor or
Extended Microcontroller
mode
(Note 5)
Terminated via internal/
external interrupt or a
RESET
Conditions