P89LPC9408FBD,557 NXP Semiconductors, P89LPC9408FBD,557 Datasheet - Page 25

• Manufacturer Part Number: P89LPC9408FBD,557
• Description: IC 80C51 MCU FLASH 8K 64-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC9408FBD,557

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 64-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LED, POR, PWM, WDT
• Number Of I /o: 23
• Eeprom Size: 512 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC9x
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: OM10097 - KIT FOR LCD DEMO LPC9408EPM900K - EMULATOR/PROGRAMMER NXP P89LPC9568-4000 - DEMO BOARD SPI/I2C TO DUAL UART568-3510 - DEMO BOARD SPI/I2C TO UART568-1759 - EMULATOR DEBUGGER/PROGRMMR LPC9X
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-3228; 935280583557; P89LPC9408FBD

Philips Semiconductors
Table 7:
[1]
P89LPC9408_1
Product data sheet
Clock source
External clock input
Low/medium/high speed oscillator
(external crystal or resonator)
Required for operation above 12 MHz.
Number of I/O pins available
7.13.1.1 Quasi-bidirectional output configuration
7.13.1.2 Open-drain output configuration
7.13.1.3 Input-only configuration
7.13.1 Port configurations
All but three I/O port pins on the P89LPC9408 may be configured by software to one of
four types on a bit-by-bit basis. These are: quasi-bidirectional (standard 80C51 port
outputs), push-pull, open drain, and input-only. Two configuration registers for each port
select the output type for each port pin.
Quasi-bidirectional output type can be used as both an input and output without the need
to reconfigure the port. This is possible because when the port outputs a logic HIGH, it is
weakly driven, allowing an external device to pull the pin LOW. When the pin is driven
LOW, it is driven strongly and able to sink a fairly large current. These features are
somewhat similar to an open-drain output except that there are three pull-up transistors in
the quasi-bidirectional output that serve different purposes.
The P89LPC9408 is a 3 V device, but the pins are 5 V-tolerant. In quasi-bidirectional
mode, if a user applies 5 V on the pin, there will be a current flowing from the pin to V
causing extra power consumption. Therefore, applying 5 V in quasi-bidirectional mode is
discouraged.
A quasi-bidirectional port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
The open-drain output configuration turns off all pull-ups and only drives the pull-down
transistor of the port driver when the port latch contains a logic 0. To be used as a logic
output, a port configured in this manner must have an external pull-up, typically a resistor
tied to V
An open-drain port pin has a Schmitt trigger input that also has a glitch suppression
circuit.
The input-only port configuration has no output drivers. It is a Schmitt trigger input that
also has a glitch suppression circuit.
1. P1.5 (RST) can only be an input and cannot be configured.
2. P1.2 (SCL/T0) and P1.3 (SDA/INT0) may only be configured to be either input-only or
open-drain.
DD
.
8-bit two-clock 80C51 core with 32 segment
…continued
Reset option
No external reset (except during power-up)
External RST pin supported
No external reset (except during power-up)
External RST pin supported
Rev. 01 — 16 December 2005
[1]
[1]
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
P89LPC9408
4 LCD driver, 10-bit ADC
Number of I/O pins
(not including LCD
pins)
22
21
21
20
25 of 69
DD
,