PIC16F688-E/P Microchip Technology, PIC16F688-E/P Datasheet - Page 32

• Manufacturer Part Number: PIC16F688-E/P
• Description: IC MCU PIC FLASH 4KX14 14DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F688-E/P

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 14-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 12
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SCI/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162066 - HEADER INTRFC MPLAB ICD2 20PINAC162061 - HEADER INTRFC MPLAB ICD2 20PINDM163029 - BOARD PICDEM FOR MECHATRONICSAC162056 - HEADER INTERFACE ICD2 16F688ACICE0207 - MPLABICE 14P 300 MIL ADAPTER
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PICmicro MID-RANGE MCU FAMILY
2.1
2.2
2.2.1
DS31002A-page 2-2
Introduction
Oscillator Configurations
Oscillator Types
The internal oscillator circuit is used to generate the device clock. The device clock is required
for the device to execute instructions and for the peripherals to function. Four device clock peri-
ods generate one internal instruction clock (T
There are up to eight different modes which the oscillator may have. There are two modes which
allow the selection of the internal RC oscillator clock out (CLKOUT) to be driven on an I/O pin, or
allow that I/O pin to be used for a general purpose function. The oscillator mode is selected by
the device configuration bits. The device configuration bits are nonvolatile memory locations and
the operating mode is determined by the value written during device programming. The oscillator
modes are:
• LP
• XT
• HS
• RC
• EXTRC External Resistor/Capacitor
• EXTRC External Resistor/Capacitor with CLKOUT
• INTRC Internal 4 MHz Resistor/Capacitor
• INTRC Internal 4 MHz Resistor/Capacitor with CLKOUT
These oscillator options are made available to allow a single device type the flexibility to fit appli-
cations with different oscillator requirements. The RC oscillator option saves system cost while
the LP crystal option saves power. Configuration bits are used to select the various options. For
more details on the device configuration bits, see the
Mid-Range devices can have up to eight different oscillator modes. The user can program up to
three device configuration bits (FOSC2, FOSC1 and FOSC0) to select one of these eight modes:
• LP
• XT
• HS
• RC
• EXTRC External Resistor/Capacitor
• EXTRC External Resistor/Capacitor with CLKOUT
• INTRC Internal 4 MHz Resistor/Capacitor
• INTRC Internal 4 MHz Resistor/Capacitor with CLKOUT
The main difference between the LP, XT, and HS modes is the gain of the internal inverter of the
oscillator circuit which allows the different frequency ranges.
mation to aid in selecting an oscillator mode. In general, use the oscillator option with the lowest
possible gain which still meet specifications. This will result in lower dynamic currents (I
frequency range of each oscillator mode is the recommended (tested) frequency cutoffs, but the
selection of a different gain mode is acceptable as long as a thorough validation is performed
(voltage, temperature, component variations (Resistor, Capacitor, and internal microcontroller
oscillator circuitry)).
The RC mode and the EXTRC with CLKOUT mode have the same functionality. They are named
like this to help describe their operation vs. the other oscillator modes.
Low Frequency (Power) Crystal
Crystal/Resonator
High Speed Crystal/Resonator
External Resistor/Capacitor (same as EXTRC with CLKOUT)
Low Frequency (Power) Crystal
Crystal/Resonator
High Speed Crystal/Resonator
External Resistor/Capacitor (same as EXTRC with CLKOUT)
CY
) cycle.
“Device Characteristics”
Table 2-1
1997 Microchip Technology Inc.
and
Table 2-2
section.
give infor-
DD
). The