R5F21102DFP#U0 Renesas Electronics America, R5F21102DFP#U0 Datasheet - Page 40

• Manufacturer Part Number: R5F21102DFP#U0
• Description: IC R8C MCU FLASH 8K 32LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/R8C/Tiny/10r

Specifications of R5F21102DFP#U0

• Core Processor: R8C
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LED, WDT
• Number Of I /o: 22
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• For Use With: R0K521134S000BE - KIT EVAL STARTER FOR R8C/13R0E521134EPB00 - KIT EMULATOR PROBE FOR PC7501R0E521134CPE00 - EMULATOR COMPACT R8C/13
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/10 Group
Rev.1.20 Jan 27, 2006
REJ09B0019-0120
Table 6.4 Oscillation Stop Detection Function Specifications
Oscillation stop detectable clock and
frequency bandwidth
Enabling condition for oscillation stop
detection function
Operation at oscillation stop detection
6.5 Oscillation Stop Detection Function
The oscillation stop detection function is such that main clock oscillation circuit stop is detected. The
oscillation stop detection function can be enabled and disabled by the OCD1 to OCD0 bits in the OCD
register.
Table 6.4 lists the specifications of the oscillation stop detection function.
Where the main clock corresponds to the CPU clock source and the OCD1 to OCD0 bits are “11
(oscillation stop detection function enabled), the system is placed in the following state if the main clock
comes to a halt:
• The on-chip oscillator starts oscillation, and the on-chip oscillator clock becomes the clock source for
• OCD register OCD2 bit = 1 (selecting on-chip oscillator clock)
• OCD register OCD3 bit = 1 (main clock stopped)
• CM1 register CM14 bit = 0 (on-chip oscillator oscillating)
• Oscillation stop detection interrupt request occurs
6.5.1 How to Use Oscillation Stop Detection Function
CPU clock and peripheral functions in place of the main clock
• The oscillation stop detection interrupt shares the vector with the watchdog timer interrupt. If the
• Where the main clock re-oscillated after oscillation stop, the clock source for the CPU clock and
• To enter wait mode while using the oscillation stop detection function, set the CM02 bit to “0” (periph-
• Since the oscillation stop detection function is provided in preparation for main clock stop due to
• This function cannot be used when the main clock frequency is below 2 MHz. Set the OCD1 to OCD0
oscillation stop detection and watchdog timer interrupts both are used, the interrupt factor must be
determined. Table 6.5 shows to determine the interrupt factor with the oscillation stop detection
interrupt, watchdog timer interrupt and voltage detection interrupt.
peripheral functions must be switched to the main clock in the program.
Figure 6.6 shows the procedure for switching the clock source from the on-chip oscillator to the main
clock.
eral function clocks not turned off during wait mode).
external factors, set the OCD1 to OCD0 bits to “00
where the main clock is stopped or oscillated in the program, that is where the stop mode is selected
or the CM05 bit is altered.
bits to “00
Item
2
” (oscillation stop detection function disabled).
page 28 of 180
f(X
Set OCD1 to OCD0 bits to “11
function enabled)
Oscillation stop detection interrupt occurs
IN
)
2 MHz
2
” (oscillation stop detection function disabled)
Specification
6.5 Oscillation Stop Detection Function
2
” (oscillation stop detection
2
”