C8051F988-GM Silicon Laboratories Inc, C8051F988-GM Datasheet - Page 294

• Manufacturer Part Number: C8051F988-GM
• Description: IC MCU 8BIT 4KB FLASH 24QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F988-GM

• Program Memory Type: FLASH
• Program Memory Size: 4KB (4K x 8)
• Package / Case: 24-UQFN Exposed Pad, 24-HUQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Ram Size: 512 B
• Interface Type: I2C, SMBus, Enhanced UART, Enhanced SPI
• Maximum Clock Frequency: 7 KHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.4 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F996DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• On-chip Dac: 10 bit, 4 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1959-5

C8051F99x-C8051F98x
25.3.3. SmaRTClock/External Oscillator Capture Mode
The Capture Mode in Timer 3 allows either SmaRTClock or the external oscillator period to be measured
against the system clock or the system clock divided by 12. SmaRTClock and the external oscillator period
can also be compared against each other.
Setting TF3CEN to 1 enables the SmaRTClock/External Oscillator Capture Mode for Timer 3. In this mode,
T3SPLIT should be set to 0, as the full 16-bit timer is used.
When Capture Mode is enabled, a capture event will be generated either every SmaRTClock rising edge
or every 8 external clock cycles, depending on the T3XCLK1 setting. When the capture event occurs, the
contents of Timer 3 (TMR3H:TMR3L) are loaded into the Timer 3 reload registers (TMR3RLH:TMR3RLL)
and the TF3H flag is set (triggering an interrupt if Timer 3 interrupts are enabled). By recording the differ-
ence between two successive timer capture values, the SmaRTClock or external clock period can be
determined with respect to the Timer 3 clock. The Timer 3 clock should be much faster than the capture
clock to achieve an accurate reading.
For example, if T3ML = 1b, T3XCLK1 = 0b, and TF3CEN = 1b, Timer 3 will clock every SYSCLK and cap-
ture every SmaRTClock rising edge. If SYSCLK is 24.5 MHz and the difference between two successive
captures is 350 counts, then the SmaRTClock period is as follows:
350 x (1 / 24.5 MHz) = 14.2 µs.
This mode allows software to determine the exact frequency of the external oscillator in C and RC mode or
the time between consecutive SmaRTClock rising edges, which is useful for determining the SmaRTClock
frequency.
294
E xtern al C lock/8
E xte rna l C lock/8
S m a R T C lo ck
S Y S C LK /12
S m aR T C loc k
S Y S C LK
T 3X C L K [1:0]
T 3X C L K 1
X 0
01
11
1
0
Figure 25.9. Timer 3 Capture Mode Block Diagram
M
H
T
3
M
0
1
T
3
L
C K C O N
M
T
2
H
T
M
2
L
M
T
1
T F 3 C E N
M
T
0
S
C
A
1
T R 3
S
C
A
0
Rev. 1.0
C ap ture
T C L K
T M R 3R LL T M R 3 R LH
T M R 3L
T M R 3 H
T 3X C L K 1
T 3X C L K 0
T F 3 C E N
T 3 S P LIT
T F 3 L E N
T F 3H
T F 3 L
T R 3
Interrupt