C8051F988-GM Silicon Laboratories Inc, C8051F988-GM Datasheet - Page 190

• Manufacturer Part Number: C8051F988-GM
• Description: IC MCU 8BIT 4KB FLASH 24QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F988-GM

• Program Memory Type: FLASH
• Program Memory Size: 4KB (4K x 8)
• Package / Case: 24-UQFN Exposed Pad, 24-HUQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Ram Size: 512 B
• Interface Type: I2C, SMBus, Enhanced UART, Enhanced SPI
• Maximum Clock Frequency: 7 KHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.4 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F996DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• On-chip Dac: 10 bit, 4 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1959-5

C8051F99x-C8051F98x
19.3.3. External Capacitor Mode
If a capacitor is used as the external oscillator, the circuit should be configured as shown in Figure 19.1,
Option 3. The capacitor should be added to XTAL2, and XTAL2 should be configured for analog I/O with
the digital output drivers disabled. XTAL1 is not affected in RC mode.
The capacitor should be no greater than 100 pF; however, for very small capacitors, the total capacitance
may be dominated by parasitic capacitance in the PCB layout. The oscillation frequency and the required
External Oscillator Frequency Control value (XFCN) in the OSCXCN Register can be determined by the
following equation:
where
f = frequency of clock in MHzR = pull-up resistor value in k
V
Below is an example of selecting the capacitor and finding the frequency of oscillation Assume V
and f = 150 kHz:
Since a frequency of roughly 150 kHz is desired, select the K Factor from Table 19.2 as KF = 22:
Therefore, the XFCN value to use in this example is 011 and C is approximately 50 pF.
The recommended startup procedure for C mode is the same as RC mode.
19.3.4. External CMOS Clock Mode
If an external CMOS clock is used as the external oscillator, the clock should be directly routed into XTAL2.
The XTAL2 pin should be configured as a digital input. XTAL1 is not used in external CMOS clock mode.
The external oscillator valid detector will always return zero when the external oscillator is configured to
External CMOS Clock mode.
190
DD
0.150 MHz
C
0.150 MHz
f
f
=
= power supply voltage in VoltsC = capacitor value on the XTAL2 pin in pF
=
=
---------------------------------------------- -
0.150 MHz 3.0 V
C
-------------------- -
C V
-------------------- -
C V
=


KF
KF
48.8 pF
=
DD
DD
=
22
---------------------- -
C 3.0 V
-----------------
C 3.0


KF

22
Rev. 1.0
DD
= 3.0 V