ST72F324BJ6T6 STMicroelectronics, ST72F324BJ6T6 Datasheet - Page 146

• Manufacturer Part Number: ST72F324BJ6T6
• Description: IC MCU 8BIT 32K FLASH 44-LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F324BJ6T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 497-6421 - BOARD EVAL DGTL BATT CHGR DESIGN497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-5590

Electrical characteristics
12.1.5
12.2
12.2.1
146/198
Pin input voltage
The input voltage measurement on a pin of the device is described in
Figure 61. Pin input voltage
Absolute maximum ratings
Stresses above those listed as “absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Voltage characteristics
Table 83.
1. Directly connecting the RESET and I/O pins to V
2. I
|V
internal reset is generated or an unexpected change of the I/O configuration occurs (for example, due to a
corrupted program counter). To guarantee safe operation, this connection has to be done through a pull-up
or pull-down resistor (typical: 4.7k for RESET, 10k for I/Os). For the same reason, unused I/O pins
must not be directly tied to V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
pads, there is no positive injection current, and the corresponding V
respected.
DDx
|V
INJ(PIN)
V
V
V
V
SSA
Symbol
V
ESD(HBM)
DD
PP
ESD(MM)
| and |V
IN
(1)(2)
- V
- V
- V
must never be exceeded. This is implicitly ensured if V
SS
SS
SSx
Voltage characteristics
SSx
|
| Variations between different digital power pins
Supply voltage
Programming voltage
Input voltage on true open drain pin
Input voltage on any other pin
Variations between digital and analog ground pins
Electrostatic discharge voltage (human body model)
Electrostatic discharge voltage (machine model)
IN
> V
DD
DD
or V
while a negative injection is induced by V
Doc ID13466 Rev 4
SS
.
V
IN
Ratings
DD
or V
SS
ST7 pin
could damage the device if an unintentional
IN
maximum is respected. If V
IN
maximum must always be
IN
INJ(PIN)
< V
SS
. For true open-drain
value. A positive
Figure
Maximum value Unit
see
V
SS
V
V
SS
Section 12.8.3 on
DD
- 0.3 to 6.5
ST72324B-Auto
page 160
6.5
13
- 0.3 to
50
50
61.
+ 0.3
IN
maximum
mV
V