PIC18C442-I/P Microchip Technology, PIC18C442-I/P Datasheet - Page 92

• Manufacturer Part Number: PIC18C442-I/P
• Description: IC MCU OTP 8KX16 A/D 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C442-I/P

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 33
• Program Memory Type: OTP
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC18
• No. Of I/o's: 34
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: MSSP, SPI, I2C, PSP, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: I3DB18C452 - BOARD DAUGHTER ICEPIC3444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18CXX2
8.6
The Parallel Slave Port is implemented on the 40-pin
devices only (PIC18C4X2).
PORTD operates as an 8-bit wide, parallel slave port,
or microprocessor port, when control bit PSPMODE
(TRISE<4>) is set. It is asynchronously readable and
writable by the external world through RD control input
pin RE0/RD and WR control input pin RE1/WR.
It can directly interface to an 8-bit microprocessor data
bus. The external microprocessor can read or write the
PORTD latch as an 8-bit latch. Setting bit PSPMODE
enables port pin RE0/RD to be the RD input, RE1/WR
to be the WR input and RE2/CS to be the CS (chip
select) input. For this functionality, the corresponding
data direction bits of the TRISE register (TRISE<2:0>)
must be configured as inputs (set). The A/D port config-
uration bits PCFG2:PCFG0 (ADCON1<2:0>) must be
set, which will configure pins RE2:RE0 as digital I/O.
A write to the PSP occurs when both the CS and WR
lines are first detected low. A read from the PSP occurs
when both the CS and RD lines are first detected low.
The PORTE I/O pins become control inputs for the
microprocessor port when bit PSPMODE (TRISE<4>)
is set. In this mode, the user must make sure that the
TRISE<2:0> bits are set (pins are configured as digital
inputs), and the ADCON1 is configured for digital I/O.
In this mode, the input buffers are TTL.
FIGURE 8-11:
DS39026C-page 90
PORTD<7:0>
PSPIF
Parallel Slave Port
OBF
CS
WR
RD
IBF
Q1
PARALLEL SLAVE PORT WRITE WAVEFORMS
Q2
Q3
Q4
Q1
Q2
FIGURE 8-10:
One bit of PORTD
Data Bus
Q3
Set Interrupt Flag
PSPIF (PIR1<7>)
Note: I/O pin has protection diodes to V
WR LATD
or
PORTD
RD PORTD
RD LATD
Q4
Data Latch
Q
D
CK
Q1
EN
EN
Q
D
PORTD AND PORTE
BLOCK DIAGRAM
(PARALLEL SLAVE
PORT)
2001 Microchip Technology Inc.
Q2
Chip Select
Read
Write
Q3
TTL
TTL
TTL
TTL
DD
Q4
and V
SS
RDx
pin
RD
CS
WR
.