PIC18C442-I/P Microchip Technology, PIC18C442-I/P Datasheet - Page 25

• Manufacturer Part Number: PIC18C442-I/P
• Description: IC MCU OTP 8KX16 A/D 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C442-I/P

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 33
• Program Memory Type: OTP
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC18
• No. Of I/o's: 34
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: MSSP, SPI, I2C, PSP, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: I3DB18C452 - BOARD DAUGHTER ICEPIC3444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

2.7
When the device executes a SLEEP instruction, the
on-chip clocks and oscillator are turned off and the
device is held at the beginning of an instruction cycle
(Q1 state). With the oscillator off, the OSC1 and OSC2
signals will stop oscillating. Since all the transistor
TABLE 2-3:
2.8
Power up delays are controlled by two timers, so that
no external RESET circuitry is required for most appli-
cations. The delays ensure that the device is kept in
RESET until the device power supply and clock are sta-
ble. For additional information on RESET operation,
see the “RESET” section.
The first timer is the Power-up Timer (PWRT), which
optionally provides a fixed delay of 72 ms (nominal) on
power-up only (POR and BOR). The second timer is
the Oscillator Start-up Timer, OST, intended to keep the
chip in RESET until the crystal oscillator is stable.
Note:
2001 Microchip Technology Inc.
Effects of SLEEP Mode on the
On-chip Oscillator
Power-up Delays
LP, XT, and HS
See Table 3-1, in Section 3.0 RESET, for time-outs due to SLEEP and MCLR Reset.
OSC Mode
RCIO
ECIO
RC
EC
OSC1 AND OSC2 PIN STATES IN SLEEP MODE
Floating, external resistor should
Floating, external resistor should
Feedback inverter disabled, at
quiescent voltage level
OSC1 Pin
pull high
pull high
Floating
Floating
switching currents have been removed, SLEEP mode
achieves the lowest current consumption of the device
(only leakage currents). Enabling any on-chip feature
that will operate during SLEEP will increase the current
consumed during SLEEP. The user can wake from
SLEEP through external RESET, Watchdog Timer
Reset, or through an interrupt.
With the PLL enabled (HS/PLL oscillator mode), the
time-out sequence following a Power-on Reset is differ-
ent from other oscillator modes. The time-out sequence
is as follows: First, the PWRT time-out is invoked after
a POR time delay has expired. Then, the Oscillator
Start-up Timer (OST) is invoked. However, this is still
not a sufficient amount of time to allow the PLL to lock
at high frequencies. The PWRT timer is used to provide
an additional fixed 2ms (nominal) time-out to allow the
PLL ample time to lock to the incoming clock frequency.
Feedback inverter disabled, at
Configured as PORTA, bit 6
Configured as PORTA, bit 6
quiescent voltage level
PIC18CXX2
At logic low
At logic low
OSC2 Pin
DS39026C-page 23