DSPIC33FJ32GS406-I/PT Microchip Technology, DSPIC33FJ32GS406-I/PT Datasheet - Page 267

• Manufacturer Part Number: DSPIC33FJ32GS406-I/PT
• Description: IC MCU/DSP 32KB FLASH 64TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ32GS406-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SCI, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, QEI, POR, PWM, WDT
• Number Of I /o: 58
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Core Frequency: 40MHz
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 53
• Flash Memory Size: 32KB
• Supply Voltage Range: 3V To 3.6V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

REGISTER 19-1:
 2010 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
dsPIC33FJ32GS406/606/608/610 and dsPIC33FJ64GS406/606/608/610
I2CEN
R/W-0
R/W-0
GCEN
I2CEN: I2Cx Enable bit
1 = Enables the I2Cx module and configures the SDAx and SCLx pins as serial port pins
0 = Disables the I2Cx module. All I
Unimplemented: Read as ‘0’
I2CSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters an Idle mode
0 = Continue module operation in Idle mode
SCLREL: SCLx Release Control bit (when operating as I
1 = Release SCLx clock
0 = Hold SCLx clock low (clock stretch)
If STREN = 1:
Bit is R/W (i.e., software can write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware clear
at beginning of slave transmission. Hardware clear at end of slave reception.
If STREN = 0:
Bit is R/S (i.e., software can only write ‘1’ to release clock). Hardware clear at beginning of slave
transmission.
IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit
1 = IPMI mode is enabled; all addresses Acknowledged
0 = IPMI mode disabled
A10M: 10-Bit Slave Address bit
1 = I2CxADD is a 10-bit slave address
0 = I2CxADD is a 7-bit slave address
DISSLW: Disable Slew Rate Control bit
1 = Slew rate control disabled
0 = Slew rate control enabled
SMEN: SMBus Input Levels bit
1 = Enable I/O pin thresholds compliant with SMBus specification
0 = Disable SMBus input thresholds
GCEN: General Call Enable bit (when operating as I
1 = Enable interrupt when a general call address is received in the I2CxRSR
0 = General call address disabled
STREN: SCLx Clock Stretch Enable bit (when operating as I
Used in conjunction with SCLREL bit.
1 = Enable software or receive clock stretching
0 = Disable software or receive clock stretching
STREN
R/W-0
U-0
(module is enabled for reception)
—
I2CxCON: I2Cx CONTROL REGISTER
U = Unimplemented bit, read as ‘0’
W = Writable bit
‘1’ = Bit is set
I2CSIDL
ACKDT
R/W-0
R/W-0
R/W-1, HC
R/W-0, HC
SCLREL
ACKEN
Preliminary
2
C pins are controlled by port functions.
HS = Hardware Settable bit
‘0’ = Bit is cleared
R/W-0, HC
IPMIEN
R/W-0
RCEN
2
C slave)
R/W-0, HC
2
C slave)
R/W-0
A10M
PEN
2
C slave)
HC = Hardware Clearable bit
x = Bit is unknown
R/W-0, HC
DISSLW
R/W-0
RSEN
DS70591C-page 267
R/W-0, HC
R/W-0
SMEN
SEN
bit 8
bit 0