MC10XS4200FK Freescale Semiconductor, MC10XS4200FK Datasheet - Page 19

• Manufacturer Part Number: MC10XS4200FK
• Description: Power Switch ICs - Power Distribution 24v 10MOHM DUAL HI-SIDE
• Manufacturer: Freescale Semiconductor

Specifications of MC10XS4200FK

• Rohs: yes
• On Resistance (max): 18 mOhms
• Operating Supply Voltage: 8 V to 36 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Package / Case: PQFN-23
• Minimum Operating Temperature: - 40 C

Table 4. Dynamic Electrical Characteristics (continued)
average values evaluated under nominal conditions T
Analog Integrated Circuit Device Data
Freescale Semiconductor
SPI INTERFACE ELECTRICAL CHARACTERISTICS
Notes
Maximum Operating Frequency of the Serial Peripheral Interface (SPI)
Required Low-state Duration for reset RSTB
Required duration from the Rising to the Falling Edge of CSB (Required Setup
Time)
Rising Edge of RSTB to Falling Edge of CSB (Required Setup Time)
Falling Edge of CSB to Rising Edge of SCLK (Required Setup Time)
Required High State Duration of SCLK (Required Setup Time)
Required Low State Duration of SCLK (Required Setup Time)
Falling Edge of SCLK to Rising Edge of CSB (Required Setup Time)
SI to Falling Edge of SCLK (Required Setup Time)
Falling Edge of SCLK to SI (Required Setup Time)
SO Rise Time
SO Fall Time
SI, CSB, SCLK, Max. Rise Time allowing operation at f
SI, CSB, SCLK, Max. Fall Time allowing operation at f
Time from Rising Edge of
Time from Rising Edge of
38.
39.
40.
41.
42.
43.
44.
Unless specified otherwise: 8.0 V ≤ V
C
C
L
L
(40)
= 80 pF
= 80 pF
Parameters guaranteed by design. It is recommended to tie unused SPI pins to GND with resistors 1.0k < R <10 k
RSTB low duration defined as the minimum time required to switch off the channel when previously put ON in SPI mode (direct inputs
inactive).
Minimum setup time required for the device is the minimum required time that the microcontroller must wait or remain in a given state.
Rise and Fall time of incoming SI, CSB, and SCLK signals.
Time required for output data to be available for use at SO, measured with a 1.0 kΩ series resistor connected CSB.
Time required for output data to be terminated at SO measured with a 1.0 kΩ series resistor connected CSB.
For clock frequencies > 4.0 MHz, series resistors on the SPI pins should preferably be removed. Otherwise, 470 pF (V
ceramic speed-up capacitors in parallel with the >8.0 kΩ input resistors are required on pins SCLK, SI, SO, and CS.
SCLK
SCLK
to the SO Low-level
to the SO High-level
Parameter
PWR
(39)
≤ 36 V, 3.0 V ≤ V
(41)
(41)
(42)
(43)
(38)
SPI
SPI
= 8.0 MHz
= 8.0 MHz
A
=
(40)
(40)
25 °C,V
(41)
DD
(40)
(40)
(40)
(41)
(44)
≤ 5.5 V, - 40 °C ≤ T
PWR
= 28 V & V
t
t
Symbol
t
t
t
SI (HOLD)
t
WSCLKh
t
WSCLKl
SO(DIS)
WRSTB
t
SO(EN)
t
t
t
SI (SU)
t
t
LEAD
t
f
ENBL
t
LAG
RSO
FSO
CSB
SPI
RSI
FSI
DD
A
DYNAMIC ELECTRICAL CHARACTERISTICS
= 5.0 V, unless specified otherwise.
≤ 125 °C, GND = 0 V. Typical values are
Min
500
1.0
5.0
10
50
50
60
37
49
–
–
–
–
–
–
–
ELECTRICAL CHARACTERISTICS
Typ
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Max
8.0
MAX.
20
20
12
12
73
73
–
–
–
–
–
–
–
–
–
> 40 V)
10XS4200
MHz
Unit
μs
μs
μs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
19