AT90PWM161 Atmel Corporation, AT90PWM161 Datasheet - Page 264

• Manufacturer Part Number: AT90PWM161
• Manufacturer: Atmel Corporation

Specifications of AT90PWM161

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 20
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 8
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

Table 21-15.
Note:
21.8.4
264
Instruction
Write EEPROM Memory Page
(page access)
Read Lock bits
Write Lock bits
Read Signature Byte
Write Fuse bits
Write Fuse High bits
Write Extended Fuse Bits
Read Fuse bits
Read Fuse High bits
Read Extended Fuse Bits
Read Calibration Byte
Poll RDY/BSY
a = address high bits, b = address low bits, H = 0 - Low byte, 1 - High Byte, o = data out, i = data in, x = don’t care
AT90PWM81
SPI Serial Programming Characteristics
Serial Programming Instruction Set (Continued)
For characteristics of the SPI module see “SPI Serial Programming Characteristics” on page 264.
1100 0010
1010 1100
0101 0000
1111 0000
0101 1000
0101 0000
0101 1000
1010 1100
0011 0000
1010 1100
1010 1100
0011 1000
Byte 1
00xx xxaa
1010 0100
0000 1000
0000 0000
0000 0000
1010 0000
1010 1000
0000 0000
0000 1000
000x xxxx
000x xxxx
111x xxxx
Byte 2
Instruction Format
bbbb bb00
xxxx xxxx
xxxx xxxx
xxxx xxxx
0000 0000
xxxx xxbb
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
Byte 3
xxxx xxxx
xxxx xxii
oooo oooo
xxxx xxxo
oooo oooo
oooo oooo
oooo oooo
oooo oooo
xxoo oooo
11ii iiii
Byte4
iiii iiii
iiii iiii
Operation
Write EEPROM page at address a:b.
Read Lock bits. “0” = programmed, “1” =
unprogrammed. See
247
Write Lock bits. Set bits = “0” to program
Lock bits. See
details.
Read Signature Byte o at address b.
Set bits = “0” to program, “1” to
unprogram. See Table XXX on page
XXX for details.
Set bits = “0” to program, “1” to
unprogram. See
for details.
Set bits = “0” to program, “1” to
unprogram. See
for details.
Read Fuse bits. “0” = programmed, “1” =
unprogrammed. See Table XXX on page
XXX for details.
Read Fuse High bits. “0” = pro-grammed,
“1” = unprogrammed. See
page 251
Read Extended Fuse bits. “0” = pro-
grammed, “1” = unprogrammed. See
Table 21-4 on page 249
Read Calibration Byte
If o = “1”, a programming operation is still
busy. Wait until this bit returns to “0”
before applying another command.
for details.
for details.
Table 21-1 on page 247
Table 21-4 on page 249
Table 21-5 on page 251
Table 21-1 on page
Table 21-5 on
for details.
7734P–AVR–08/10
for