AT90PWM1 Atmel Corporation, AT90PWM1 Datasheet - Page 237

• Manufacturer Part Number: AT90PWM1
• Manufacturer: Atmel Corporation

Specifications of AT90PWM1

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

Table 88. Serial Programming Instruction Set (Continued)
Note:
22.9.4
4378C–AVR–09/08
Instruction
Load EEPROM Memory
Page (page access)
Write EEPROM Memory
Page (page access)
Read Lock bits
Write Lock bits
Read Signature Byte
Write Fuse bits
Write Fuse High bits
Write Extended Fuse Bits
Read Fuse bits
Read Fuse High bits
Read Extended Fuse Bits
Read Calibration Byte
Poll RDY/BSY
a = address high bits, b = address low bits, H = 0 - Low byte, 1 - High Byte, o = data out, i = data in, x = don’t care
SPI Serial Programming Characteristics
For characteristics of the SPI module see “SPI Serial Programming Characteristics” on page
237.
1100 0001
1100 0010
0101 1000
1010 1100
0011 0000
1010 1100
1010 1100
1010 1100
0101 0000
0101 1000
0101 0000
0011 1000
1111 0000
Byte 1
0000 0000
00xx xxaa
0000 0000
111x xxxx
000x xxxx
1010 0000
1010 1000
1010 0100
0000 0000
0000 1000
0000 1000
000x xxxx
0000 0000
Byte 2
Instruction Format
0000 00bb
bbbb bb00
xxxx xxxx
xxxx xxxx
xxxx xxbb
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
0000 0000
xxxx xxxx
Byte 3
iiii iiii
xxxx xxxx
xxoo oooo
11ii iiii
oooo oooo
iiii iiii
iiii iiii
xxxx xxii
oooo oooo
oooo oooo
oooo oooo
oooo oooo
xxxx xxxo
Byte4
Operation
Load data i to EEPROM memory page
buffer. After data is loaded, program
EEPROM page.
Write EEPROM page at address a:b.
Read Lock bits. “0” = programmed, “1”
= unprogrammed. See
page 219
Write Lock bits. Set bits = “0” to
program Lock bits. See
page 219
Read Signature Byte o at address b.
Set bits = “0” to program, “1” to
unprogram. See Table XXX on page
XXX for details.
Set bits = “0” to program, “1” to
unprogram. See
for details.
Set bits = “0” to program, “1” to
unprogram. See
221
Read Fuse bits. “0” = programmed, “1”
= unprogrammed. See Table XXX on
page XXX for details.
Read Fuse High bits. “0” = pro-
grammed, “1” = unprogrammed. See
Table 77 on page 222
Read Extended Fuse bits. “0” = pro-
grammed, “1” = unprogrammed. See
Table 76 on page 221
Read Calibration Byte
If o = “1”, a programming operation is
still busy. Wait until this bit returns to
“0” before applying another command.
for details.
for details.
for details.
AT90PWM1
Table 77 on page 222
Table 76 on page
for details.
Table 73 on
Table 73 on
for details.
237