AT90PWM1 Atmel Corporation, AT90PWM1 Datasheet - Page 234

• Manufacturer Part Number: AT90PWM1
• Manufacturer: Atmel Corporation

Specifications of AT90PWM1

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

22.9
22.9.1
234
Serial Downloading
AT90PWM1
Serial Programming Algorithm
Table 86. Parallel Programming Characteristics, V
Notes:
Both the Flash and EEPROM memory arrays can be programmed using the serial SPI bus while
RESET is pulled to GND. The serial interface consists of pins SCK, MOSI (input) and MISO (out-
put). After RESET is set low, the Programming Enable instruction needs to be executed first
before program/erase operations can be executed. NOTE, in
mapping for SPI programming is listed. Not all parts use the SPI pins dedicated for the internal
SPI interface.
Figure 22-10. Serial Programming and Verify
Notes:
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming
operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low:> 2 CPU clock cycles for f
High:> 2 CPU clock cycles for f
When writing serial data to the AT90PWM1, data is clocked on the rising edge of SCK.
Symbol
t
t
t
BVDV
OLDV
OHDZ
1.
2. t
1. If the device is clocked by the internal Oscillator, it is no need to connect a clock source to the
2. V
commands.
XTAL1 pin.
t
WLRH_CE
CC
WLRH
Parameter
BS1 Valid to DATA valid
OE Low to DATA Valid
OE High to DATA Tri-stated
- 0.3V < AVCC < V
is valid for the Write Flash, Write EEPROM, Write Fuse bits and Write Lock bits
is valid for the Chip Erase command.
MOSI_A
MISO_A
SCK_A
ck
ck
CC
< 12 MHz, 3 CPU clock cycles for f
< 12 MHz, 3 CPU clock cycles for f
+ 0.3V, however, AVCC should always be within 1.8 - 5.5V
XTAL1
RESET
GND
(1)
CC
AVCC
= 5V ± 10% (Continued)
VCC
+1.8 - 5.5V
+1.8 - 5.5V
Table 85 on page
Min
(2)
0
ck
ck
>= 12 MHz
>= 12 MHz
Typ
Max
250
250
250
4378C–AVR–09/08
225, the pin
Units
ns
ns
ns