AT90PWM1 Atmel Corporation, AT90PWM1 Datasheet - Page 173

• Manufacturer Part Number: AT90PWM1
• Manufacturer: Atmel Corporation

Specifications of AT90PWM1

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

17.2.5
4378C–AVR–09/08
SPI Status Register – SPSR
These two bits control the SCK rate of the device configured as a Master. SPR1 and SPR0 have
no effect on the Slave. The relationship between SCK and the clk
the following table:
Table 54. Relationship Between SCK and the Oscillator Frequency
• Bit 7 – SPIF: SPI Interrupt Flag
When a serial transfer is complete, the SPIF flag is set. An interrupt is generated if SPIE in
SPCR is set and global interrupts are enabled. If SS is an input and is driven low when the SPI is
in Master mode, this will also set the SPIF flag. SPIF is cleared by hardware when executing the
corresponding interrupt handling vector. Alternatively, the SPIF bit is cleared by first reading the
SPI Status Register with SPIF set, then accessing the SPI Data Register (SPDR).
• Bit 6 – WCOL: Write COLlision Flag
The WCOL bit is set if the SPI Data Register (SPDR) is written during a data transfer. The
WCOL bit (and the SPIF bit) are cleared by first reading the SPI Status Register with WCOL set,
and then accessing the SPI Data Register.
• Bit 5..1 – Res: Reserved Bits
These bits are reserved bits in the AT90PWM1 and will always read as zero.
• Bit 0 – SPI2X: Double SPI Speed Bit
When this bit is written logic one the SPI speed (SCK Frequency) will be doubled when the SPI
is in Master mode (see
clock periods. When the SPI is configured as Slave, the SPI is only guaranteed to work at f
or lower.
The SPI interface on the AT90PWM1 is also used for program memory and EEPROM down-
loading or uploading. See
verification.
Bit
Read/Write
Initial Value
SPI2X
0
0
0
0
1
1
1
1
SPIF
R
7
0
Table
WCOL
SPR1
R
Serial Programming Algorithm234
6
0
0
0
1
1
0
0
1
1
54). This means that the minimum SCK period will be two CPU
R
5
–
0
SPR0
R
4
–
0
0
1
0
1
0
1
0
1
R
3
–
0
SCK Frequency
f
f
f
f
f
f
f
f
clkio
clkio
clkio
clkio
clkio
clkio
clkio
clkio
/
/
/
/
/
/
/
/
4
16
64
128
2
8
32
64
R
2
–
0
for
IO
serial
frequency f
R
1
–
0
AT90PWM1
programming
SPI2X
R/W
0
0
clkio
is shown in
SPSR
clkio
and
173
/4