ICS1893Y-10LF IDT, Integrated Device Technology Inc, ICS1893Y-10LF Datasheet - Page 27

• Manufacturer Part Number: ICS1893Y-10LF
• Description: PHYCEIVER LOW PWR 3.3V 64-TQFP
• Manufacturer: IDT, Integrated Device Technology Inc
• Series: PHYceiver™r
• Type: PHY Transceiverr

Specifications of ICS1893Y-10LF

• Protocol: MII
• Voltage - Supply: 3.14 V ~ 3.47 V
• Mounting Type: Surface Mount
• Package / Case: 64-TQFP, 64-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Drivers/receivers: -
• Other names: 1893Y-10LF; 800-1935-5; ICS1893Y-10LF

5.2 100M Symbol Interface
ICS1893Y-10 Rev F 1/20/04
The 100M Symbol Interface has a primary objective of supporting 100Base-TX repeater applications for
which the repeater requires only recovered parallel data and for which the repeater provides all the
necessary framing and control functions.
When the ICS1893Y-10 MAC/Repeater Interface is configured for 100M Symbol operations, the PHY and
the MAC/repeater exchange unframed 5-bit, parallel symbols at a 25-MHz clock rate.
The configuration functions of the ICS1893Y-10 determine the operation of its MAC/Repeater Interface.
The configuration functions are controlled by either input pins (in which case, the HW/SW pin is logic zero
to select the hardware mode) or Management Register bits (in which case, the HW/SW pin is logic one to
select the software mode).
•
•
The 100M Symbol Interface bypasses the ICS1893Y-10’s PCS and provides a direct, unscrambled,
unframed, 5-bit interface between the MAC/repeater and the PMA sublayer. A benefit of bypassing the
PCS is a reduction in the latency through the PHY. That is, when the ICS1893Y-10’s MAC/Repeater
Interface is configured as a 100M Symbol Interface, the bit delays through the PHY are smaller than the
standard MII Data Interface can allow. The ICS1893Y-10 provides this 100M Symbol Interface primarily for
Repeater applications, for which latency is a critical performance parameter.
In addition to the exchange of symbol data, an ICS1893Y-10 configured for 100M Symbol mode provides
ISO/IEC-compliant control signals (such as CRS) to the MAC/repeater. The ICS1893Y-10’s CRS signal
provides a fast look-ahead, which can benefit a repeater application.
In the 100M Symbol Interface mode, the ICS1893Y-10 continues to assert the CRS signal using its PCS
logic. This action does not affect the bit delay or latency because the PCS CRS logic examines the bits
received from the PMA sublayer serially. In fact, because the PCS CRS does not wait for a nibble or symbol
to be constructed, the PCS CRS is available in advance of the symbol generation. Therefore, by using the
PCS CRS generation logic, the ICS1893Y-10 can provide an ‘early’ indication of a Carrier Detect to the
MAC/repeater.
The 100M Symbol Interface consists of the following fourteen signals:
•
•
•
•
•
•
When the ICS1893Y-10 MAC/Repeater Interface is configured for 100M Symbol operations, its default MII
pin names and their associated functions are redefined. For more information, see
“MAC/Repeater Interface Pins for 100M Symbol
In hardware mode, the ICS1893Y-10 enables the 100M Symbol Interface when both of the following are
true:
In software mode, the ICS1893Y-10 enables the 100M Symbol Interface when both the following are
true:
SCRS
SD
SRCLK
SRD[4:0]
STCLK
STD[4:0]
– Its MII/SI input pin is sampled as a logic one (that is, the selection is for the Symbol Interface).
– Its 10/100SEL input pin is sampled as a logic one (that is, the selection is for 100M operations).
– Its MII/SI input pin is sampled as a logic one (that is, the selection is for the Symbol Interface).
– Its Control Register Data Rate bit (bit 0.13) is set to logic one (that is, the selection is for selecting
ICS1893Y-10 - Release
100M operations)
Copyright © 2004, Integrated Circuit Systems, Inc.
All rights reserved.
27
Interface”.
Chapter 5 Interface Overviews
Section 8.3.4.2,
January, 2004