PIC18F65K90T-I/PT Microchip Technology, PIC18F65K90T-I/PT Datasheet - Page 213

• Manufacturer Part Number: PIC18F65K90T-I/PT
• Description: 32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F65K90T-I/PT

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP
• Lead Free Status / Rohs Status: Details

16.0
The Timer4/6/8/10/12 timer modules have the following
features:
• 8-Bit Timer register (TMRx)
• 8-Bit Period register (PRx)
• Readable and writable (all registers)
• Software programmable prescaler (1:1, 1:4, 1:16)
• Software programmable postscaler (1:1 to 1:16)
• Interrupt on TMRx match of PRx
Timer10 and Timer12 are unimplemented for devices
with a program memory of 32 Kbytes (PIC18FX5K90).
The Timer4/6/8/10/12 modules have a control register,
which is shown in
be shut off by clearing control bit, TMRxON (TxCON<2>),
to minimize power consumption. The prescaler and post-
scaler selection of Timer4/6/8/10/12 are also controlled
by this register.
of the Timer4/6/8/10/12 modules.
 2009-2011 Microchip Technology Inc.
Note: Throughout this section, generic references
TIMER4/6/8/10/12 MODULES
are used for register and bit names that are the
same, except for an ‘x’ variable that indicates
the item’s association with the Timer4, Timer6,
Timer8, Timer10 or Timer12 module. For
example, the control register is named TxCON
and refers to T4CON, T6CON, T8CON,
T10CON and T12CON.
Figure 16-1
Register
is a simplified block diagram
16-1. Timer4/6/8/10/12 can
PIC18F87K90 FAMILY
16.1
Timer4/6/8/10/12 can be used as the PWM time base
for the PWM mode of the ECCP modules. The TMRx
registers are readable and writable, and are cleared on
any device Reset. The input clock (F
prescale option of 1:1, 1:4 or 1:16, selected by control
bits, TxCKPS<1:0> (TxCON<1:0>). The match output
of TMRx goes through a 4-bit postscaler (that gives a
1:1 to 1:16 inclusive scaling) to generate a TMRx
interrupt, latched in the flag bit, TMRxIF.
shows each module’s flag bit.
TABLE 16-1:
The interrupt can be enabled or disabled by setting or
clearing the Timerx Interrupt Enable bit (TMRxIE),
shown in
TABLE 16-2:
The prescaler and postscaler counters are cleared
when any of the following occurs:
• A write to the TMRx register
• A write to the TxCON register
• Any device Reset (Power-on Reset (POR), MCLR
A TMRx is not cleared when a TxCON is written.
Reset, Watchdog Timer Reset (WDTR) or
Brown-out Reset (BOR))
Note:
Module
Module
Timer
Timer
4
6
8
4
6
8
Timer4/6/8/10/12 Operation
Table
The CCP and ECCP modules use Timers,
1 through 8, for some modes. The assign-
ment of a particular timer to a CCP/ECCP
module is determined by the Timer to CCP
enable bits in the CCPTMRSx registers.
For more details, see
Register 18-2
16-2.
PIR5<x>
PIE5<x>
Flag Bit
Flag Bit
TIMER4/6/8/10/12 FLAG BITS
TIMER4/6/8/10/12 INTERRUPT
ENABLE BITS
0
2
4
0
2
4
and
Module
Module
Register
Timer
Timer
10
12
10
12
DS39957D-page 213
Register
18-3.
OSC
PIR5<x>
PIE5<x>
Flag Bit
Flag Bit
Table 16-1
/4) has a
5
6
5
6
19-2,