PIC18F85K22-I/PT Microchip Technology, PIC18F85K22-I/PT Datasheet - Page 342

• Manufacturer Part Number: PIC18F85K22-I/PT
• Description: IC, 8BIT MCU, PIC18F, 64MHZ, TQFP-80
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F85K22-I/PT

• Controller Family/series: PIC18
• No. Of I/o's: 69
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2KB
• Cpu Speed: 64MHz
• No. Of Timers: 8
• Core Size: 8 Bit
• Program Memory Size: 32KB
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: EBI/EMI, I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F87K22 FAMILY
22.2.4
During Sleep mode, all clocks to the EUSART are
suspended. Because of this, the Baud Rate Generator
is inactive and a proper byte reception cannot be per-
formed. The auto-wake-up feature allows the controller
to wake up due to activity on the RXx/DTx line while the
EUSART is operating in Asynchronous mode.
The auto-wake-up feature is enabled by setting the
WUE bit (BAUDCONx<1>). Once set, the typical
receive sequence on RXx/DTx is disabled and the
EUSART remains in an Idle state, monitoring for a
wake-up event independent of the CPU mode. A
wake-up event consists of a high-to-low transition on
the RXx/DTx line. (This coincides with the start of a
Sync Break or a Wake-up Signal character for the
LIN/J2602 protocol.)
Following a wake-up event, the module generates an
RCxIF interrupt. The interrupt is generated synchro-
nously to the Q clocks in normal operating modes
(Figure
Sleep mode
cleared by reading the RCREGx register.
The WUE bit is automatically cleared once a low-to-high
transition is observed on the RXx line following the
wake-up event. At this point, the EUSART module is in
Idle mode and returns to normal operation. This signals
to the user that the Sync Break event is over.
DS39960D-page 342
22-8) and asynchronously if the device is in
AUTO-WAKE-UP ON SYNC BREAK
CHARACTER
(Figure
22-9). The interrupt condition is
22.2.4.1
Since auto-wake-up functions by sensing rising edge
transitions on RXx/DTx, information with any state
changes before the Stop bit may signal a false
End-of-Character (EOC) and cause data or framing
errors. To work properly, therefore, the initial character
in the transmission must be all ‘0’s. This can be 00h
(8 bits) for standard RS-232 devices or 000h (12 bits)
for the LIN/J2602 bus.
Oscillator start-up time must also be considered,
especially in applications using oscillators with longer
start-up intervals (i.e., HS or HSPLL mode). The Sync
Break (or Wake-up Signal) character must be of
sufficient length and be followed by a sufficient interval
to allow enough time for the selected oscillator to start
and provide proper initialization of the EUSART.
Special Considerations Using
Auto-Wake-up
 2009-2011 Microchip Technology Inc.