C8051F018-GQ Silicon Laboratories Inc, C8051F018-GQ Datasheet - Page 68

• Manufacturer Part Number: C8051F018-GQ
• Description: IC 8051 MCU 16K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F018r

Specifications of C8051F018-GQ

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 64-TQFP, 64-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Operating Supply Voltage: 2.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1197

If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode. The
Missing Clock Detector should be disabled if the CPU is to be put to sleep for longer than the MCD timeout of
100sec.
Bit7:
Bits6-2: GF4-GF0: General Purpose Flags 4-0.
Bit1:
Bit0:
SMOD
R/W
Bit7
SMOD: Serial Port Baud Rate Doubler Enable.
0: Serial Port baud rate is that defined by Serial Port Mode in SCON.
1: Serial Port baud rate is double that defined by Serial Port Mode in SCON.
These are general purpose flags for use under software control.
Setting this bit will place the CIP-51 in Stop mode. This bit will always be read as 0.
1: Goes into power down mode. (Turns off internal oscillator).
Setting this bit will place the CIP-51 in Idle mode. This bit will always be read as 0.
1: Goes into idle mode. (Shuts off clock to CPU, but clock to Timers, Interrupts, Serial
STOP: Stop Mode Select.
IDLE: Idle Mode Select.
Ports, and Analog Peripherals are still active.)
GF4
R/W
Bit6
R/W
GF3
Bit5
Figure 8.15. PCON: Power Control Register
R/W
GF2
Bit4
Rev. 1.2
GF1
R/W
Bit3
R/W
GF0
Bit2
STOP
R/W
Bit1
C8051F018
C8051F019
IDLE
R/W
Bit0
SFR Address:
Reset Value
00000000
0x87
68