PIC18F6527-I/PT Microchip Technology, PIC18F6527-I/PT Datasheet - Page 231

• Manufacturer Part Number: PIC18F6527-I/PT
• Description: IC PIC MCU FLASH 24KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6527-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 48KB (24K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

19.4.5
The addressing procedure for the I
the first byte after the Start condition usually
determines which device will be the slave addressed by
the master. The exception is the general call address
which can address all devices. When this address is
used, all devices should, in theory, respond with an
Acknowledge.
The general call address is one of eight addresses
reserved for specific purposes by the I
consists of all ‘0’s with R/W = 0.
The general call address is recognized when the
General
(SSPxCON2<7> set). Following a Start bit detect, 8 bits
are shifted into the SSPxSR and the address is
compared against the SSPxADD. It is also compared to
the general call address and fixed in hardware.
FIGURE 19-15:
© 2008 Microchip Technology Inc.
GCEN (SSPxCON2<7>)
SSPOV (SSPxCON1<6>)
SDAx
SCLx
SSPxIF
BF (SSPxSTAT<0>)
Call
GENERAL CALL ADDRESS
SUPPORT
Enable
S
SLAVE MODE GENERAL CALL ADDRESS SEQUENCE
(7 OR 10-BIT ADDRESS MODE)
bit,
1
2
GCEN,
General Call Address
2
C bus is such that
3
2
4
C protocol. It
is
5
enabled
6
7
R/W =
8
0
If the general call address matches, the SSPxSR is
transferred to the SSPxBUF, the BF flag bit is set
(eighth bit) and on the falling edge of the ninth bit (ACK
bit), the SSPxIF interrupt flag bit is set.
When the interrupt is serviced, the source for the
interrupt can be checked by reading the contents of the
SSPxBUF. The value can be used to determine if the
address was device specific or a general call address.
In 10-bit mode, the SSPxADD is required to be updated
for the second half of the address to match and the UA
bit is set (SSPxSTAT<1>). If the general call address is
sampled when the GCEN bit is set, while the slave is
configured in 10-Bit Addressing mode, then the second
half of the address is not necessary, the UA bit will not
be set and the slave will begin receiving data after the
Acknowledge (Figure 19-15).
ACK
Address is compared to General Call Address
after ACK, set interrupt
9
PIC18F8722 FAMILY
D7
1
D6
2
Cleared in software
SSPxBUF is read
Receiving Data
D5
3
D4
4
D3
5
D2
6
D1
7
DS39646C-page 229
D0
8
ACK
9
‘
‘
0
1
’
’