PIC18F6527-I/PT Microchip Technology, PIC18F6527-I/PT Datasheet - Page 204

• Manufacturer Part Number: PIC18F6527-I/PT
• Description: IC PIC MCU FLASH 24KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6527-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 48KB (24K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F8722 FAMILY
18.4.7.1
The Auto-Shutdown feature can be configured to allow
automatic restarts of the module following a shutdown
event. This is enabled by setting the P1RSEN bit of the
ECCP1DEL register (ECCP1DEL<7>).
In Shutdown mode with P1RSEN = 1 (Figure 18-10),
the ECCP1ASE bit will remain set for as long as the
cause of the shutdown continues. When the shutdown
condition clears, the ECCP1ASE bit is cleared. If
P1RSEN = 0 (Figure 18-11), once a shutdown condi-
tion occurs, the ECCP1ASE bit will remain set until it is
cleared by firmware. Once ECCP1ASE is cleared, the
Enhanced PWM will resume at the beginning of the
next PWM period.
Independent of the P1RSEN bit setting, if the
auto-shutdown source is one of the comparators, the
shutdown condition is a level. The ECCP1ASE bit can-
not be cleared as long as the cause of the shutdown
persists.
The Auto-Shutdown mode can be forced by writing a ‘1’
to the ECCP1ASE bit.
FIGURE 18-10:
FIGURE 18-11:
DS39646C-page 202
Note:
Shutdown
Shutdown
ECCP1ASE bit
ECCP1ASE bit
PWM
PWM
Writing to the ECCP1ASE bit is disabled
while a shutdown condition is active.
Auto-Shutdown and Automatic
Restart
Activity
Activity
Event
Event
PWM Period
PWM Period
PWM AUTO-SHUTDOWN (P1RSEN =
PWM AUTO-SHUTDOWN (P1RSEN =
Start of
Start of
Normal PWM
Normal PWM
Event Occurs
Event Occurs
PWM Period
PWM Period
Shutdown
Shutdown
18.4.8
When the ECCP module is used in the PWM mode, the
application hardware must use the proper external
pull-up and/or pull-down resistors on the PWM output
pins. When the microcontroller is released from Reset,
all of the I/O pins are in the high-impedance state. The
external circuits must keep the power switch devices in
the OFF state until the microcontroller drives the I/O
pins with the proper signal levels or activates the PWM
output(s).
The CCP1M<1:0> bits (CCP1CON<1:0>) allow the
user to choose whether the PWM output signals are
active-high or active-low for each pair of PWM output
pins (P1A/P1C and P1B/P1D). The PWM output
polarities must be selected before the PWM pins are
configured as outputs. Changing the polarity configura-
tion while the PWM pins are configured as outputs is
not recommended since it may result in damage to the
application circuits.
The P1A, P1B, P1C and P1D output latches may not be
in the proper states when the PWM module is initialized.
Enabling the PWM pins for output at the same time as
the ECCP1 module may cause damage to the applica-
tion circuit. The ECCP1 module must be enabled in the
proper output mode and complete a full PWM cycle
before configuring the PWM pins as outputs. The com-
pletion of a full PWM cycle is indicated by the TMR2IF
bit being set as the second PWM period begins.
1
0
, AUTO-RESTART ENABLED)
, AUTO-RESTART DISABLED)
Event Clears
Event Clears
Shutdown
Shutdown
START-UP CONSIDERATIONS
ECCP1ASE
Cleared by
Firmware
© 2008 Microchip Technology Inc.
Resumes
Resumes
PWM
PWM