DM300024 Microchip Technology, DM300024 Datasheet - Page 68

• Manufacturer Part Number: DM300024
• Description: KIT DEMO DSPICDEM 1.1
• Manufacturer: Microchip Technology
• Type: MCUr

Specifications of DM300024

• Contents: Board, Cable, CD, Power Supply
• Silicon Manufacturer: Microchip
• Core Architecture: DsPIC
• Core Sub-architecture: DsPIC30F
• Features: Serial Communication Channels Interface, General Purpose Prototyping Area
• Silicon Core Number: DsPIC30F, DsPIC33F
• Silicon Family Name: DsPIC30F6xxx, DsPIC33FJxxGPxxx
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: dsPIC30F/33F and PIC24H
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPICDEM™ 1.1 Plus Development Board User’s Guide
DS70099D-page 64
5.1.8
A single channel digital potentiometer, MCP41010, is provided on the development
board. Control of the digital potentiometer is via the dsPIC DSC SPI 2 communication
channel. The output of the digital potentiometer is applied to a low-pass filter with a
cutoff frequency of approximately 4 kHz. The output of the LP filter is connected to the
analog channel AN3 of the dsPIC DSC device.
The schematic of the digital potentiometers is shown in Figure A-4: “dsPICDEM™ 1.1
Plus Development Board Schematic (Sheet 3 of 5)”.
5.1.9
The LCD graphic display is a PG12232D-L 8-bit 122 x 32 dot-matrix LCD controlled by
a PIC18F242 LCD controller. The dsPIC30F device accesses the LCD controller via
the SPI 2 port. For a detailed description of the communication protocol, see
Appendix B. “LCD Controller Specification”.
The LCD PIC18F242 controller is reset by setting jumper J10 to the MCLR2 position
and pressing the Reset switch. Moving jumper J10 back to the MCLR1 position returns
Reset control of the dsPIC30F device.
The schematic of the analog potentiometers is shown in Figure A-6: “dsPICDEM™
1.1 Plus Development Board Schematic (Sheet 5 of 5)”.
5.1.10
Using modular connector ICD, the MPLAB ICD 2 can be connected for low-cost
programming and debugging of the dsPIC30F/33F or PIC24H/24F device.
• Programming and debugging of dsPIC30F devices requires that jumper J8 is set
• Programming and debugging of dsPIC33F/PIC24H/PIC24F devices requires that
Programming the PIC18F242 LCD controller requires that jumper J8 is set to the
RB6/242 and RB7/242 position and jumper J10 is set to the MCLR2 position. The
PIC18F242 LCD controller is programmed at the factory with the LCD driver code.
Under normal operating conditions, no additional programming should be required for
this device.
The schematic of the analog potentiometers is shown in Figure A-6: “dsPICDEM™
1.1 Plus Development Board Schematic (Sheet 5 of 5)”
5.1.11
An Si3000 Codec from Silicon Labs is included on the development board. Stereo
Jacks provide MIC input on J16 and SPKR OUT output on J17. LINE I/O on J12
provides line-in and line-out connections. J9 provides a selection for Master or Slave
operation for the Si3000. When the Si3000 is operated in Master mode, the user must
provide a suitable clock oscillator in the U6 socket. The CODEC RESET switch resets
the Si3000.
For detailed operational information, refer to the Si3000 data sheet available on
www.silabs.com. For a schematic of the Si3000 circuit, see Figure A-6: “dsPICDEM™
1.1 Plus Development Board Schematic (Sheet 5 of 5)”.
to the 30F position and jumper J10 is set to the MCLR1 position.
jumper J8 is set to the 33F PGC1 and 33F PGD1 (or to the 33F PGC3 and 33F
PGD3) position and jumper J10 is set to the MCLR1 position.
Digital Potentiometer
LCD Graphic Display
ICD Connector
Si3000 Voice Band Codec
© 2006 Microchip Technology Inc.