DM300024 Microchip Technology, DM300024 Datasheet - Page 42

• Manufacturer Part Number: DM300024
• Description: KIT DEMO DSPICDEM 1.1
• Manufacturer: Microchip Technology
• Type: MCUr

Specifications of DM300024

• Contents: Board, Cable, CD, Power Supply
• Silicon Manufacturer: Microchip
• Core Architecture: DsPIC
• Core Sub-architecture: DsPIC30F
• Features: Serial Communication Channels Interface, General Purpose Prototyping Area
• Silicon Core Number: DsPIC30F, DsPIC33F
• Silicon Family Name: DsPIC30F6xxx, DsPIC33FJxxGPxxx
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: dsPIC30F/33F and PIC24H
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPICDEM™ 1.1 Plus Development Board User’s Guide
DS70099D-page 38
3.4.3
3.4.3.1
External interrupts INT1-INT4 are controlled by switches SW1-SW4.
These switches provide selection capabilities for the demo program. The most recent
switch presses are recorded in a variable within the interrupt routines. In the main
routine, the variable is analyzed to determine what action is requested by the recent
switch event.
3.4.3.2
The DCI module interrupts the CPU when all four TXBUF registers have been
transmitted. The DCI is used to send out DTMF tones to the Codec. The tonal
components are stored as sinusoid tables in program memory and accessed using
Program Space Visibility (PSV).
The DCI ISR keeps track of the number of samples sent. The DTMF tones are
transmitted by adhering to International Telecommunication Union (ITU-T)
specifications. For example, the ON time for tones is greater than 40 mS and the OFF
time is less than 23 mS. The actual values are 100 mS of ON time and 15 mS of OFF
time. When playing a pre-recorded sequence of tones, a PAUSE time is added
between successive tones. This time is equal to the ON time of the tone. Also, the high
and low frequency of the DTMF tone are separated by 8 dB. The high frequencies are
reduced in magnitude relative to the low frequencies by 8 dB.
3.4.3.3
Single DTMF tones may also be played by entering numeric characters (0-9) on the PC
keyboard during the HyperTerminal session. The UART receives this keyboard
character, and a receiver interrupt communicates this data to the DCI to start a tone
generation process.
3.4.3.4
Every 1.14 seconds, data is transmitted via the UART to the HyperTerminal session
window. Four bytes are loaded at a time in the Transmitter Buffer registers. The term
“data” refers to the following:
• Analog data such as RP1, RP2 and RP3
• Temperature sensor data
• FFT frequency and bin number of the sampled input sine-wave signal
• Cycle count information for the FFT, FIR or IIR algorithms
• Chosen Filter Type – IIR, FIR or None
3.4.3.5
The SPI 2 module is used to perform two functions:
• When the demo code is waiting for the ADC to collect 256 samples of data on pin
• When code execution reaches the DSP stage (i.e., filtering, FFT etc.) the SPI 2
AN3, the SPI 2 module is used by the Timer1 ISR to transmit sine-wave samples
to the MCP41010 every 125 microseconds at a data rate of 230 kHz.
module is used to send data to the PIC18F242 LCD controller on the expansion
board at a data rate of 921.6 KHz (F
display. All 80 characters are refreshed by the SPI 2 module.
Interrupts Used in the Demo
EXTERNAL INTERRUPTS TO MAIN ROUTINE
DCI INTERRUPTS AND DTMF
UART RECEIVE INTERRUPTS
UART TRANSMIT INTERRUPTS
SPI INTERRUPTS, DIGITAL POT AND THE LCD CONTROLLER
CY
/8). The LCD has a 4 row x 20-character
© 2006 Microchip Technology Inc.