STEVAL-IFS006V1 STMicroelectronics, STEVAL-IFS006V1 Datasheet - Page 54

• Manufacturer Part Number: STEVAL-IFS006V1
• Description: BOARD EVAL 8BIT MICRO + TDE1708
• Manufacturer: STMicroelectronics

Specifications of STEVAL-IFS006V1

• Design Resources: STEVAL-IFS006V1 Bill of Material
• Sensor Type: Proximity
• Interface: I²C
• Voltage - Supply: 6 V ~ 48 V
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: ST7FLITEUS5, TDE1708
• Processor To Be Evaluated: ST7LITEUS5
• Data Bus Width: 8 bit
• Operating Supply Voltage: 6 V to 48 V
• Silicon Manufacturer: ST Micro
• Silicon Core Number: TDE1708DFT
• Kit Application Type: Sensing - Touch / Proximity
• Application Sub Type: Proximity Switch
• Kit Contents: Board
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Sensitivity: -
• Sensing Range: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6403; STEVAL-IFS006V1

Power saving modes
8.5
54/136
Halt mode recommendations
●
●
●
●
●
Auto-wakeup from Halt mode
Auto-wakeup from Halt (AWUFH) mode is similar to Halt mode with the addition of a specific
internal RC oscillator for wakeup (Auto-wakeup from Halt oscillator) which replaces the main
clock which was active before entering Halt mode. Compared to Active-halt mode, AWUFH
has lower power consumption (the main clock is not kept running), but there is no accurate
realtime clock available.
It is entered by executing the HALT instruction when the AWUEN bit in the AWUCSR
register has been set.
Figure 25. AWUFH mode block diagram
As soon as Halt mode is entered, and if the AWUEN bit has been set in the AWUCSR
register, the AWU RC oscillator provides a clock signal (f
a fixed divider and a programmable prescaler controlled by the AWUPR register. The output
of this prescaler provides the delay time. When the delay has elapsed, the following actions
are performed:
●
●
●
Make sure that an external event is available to wakeup the microcontroller from Halt
mode.
When using an external interrupt to wakeup the microcontroller, reinitialize the
corresponding I/O as “Input Pull-up with Interrupt” before executing the HALT
instruction. The main reason for this is that the I/O may be wrongly configured due to
external interference or by an unforeseen logical condition.
For the same reason, reinitialize the level sensitiveness of each external interrupt as a
precautionary measure.
The opcode for the HALT instruction is 0x8E. To avoid an unexpected HALT instruction
due to a program counter failure, it is advised to clear all occurrences of the data value
0x8E from memory. For example, avoid defining a constant in ROM with the value
0x8E.
As the HALT instruction clears the I bit in the CC register to allow interrupts, the user
may choose to clear all pending interrupt bits before executing the HALT instruction.
This avoids entering other peripheral interrupt routines after executing the external
interrupt routine corresponding to the wakeup event (reset or external interrupt).
The AWUF flag is set by hardware,
An interrupt wakes-up the MCU from Halt mode,
The main oscillator is immediately turned on and the 64 CPU cycle delay is used to
stabilize it.
f
AWU_RC
AWU RC
oscillator
divider
/64
prescaler/1 .. 255
to 8-bit Timer input capture
AWUFH
(ei0 source)
AWUFH
interrupt
AWU_RC
ST7LITEUS2, ST7LITEUS5
). Its frequency is divided by