ADM1026JSTZ-REEL ON Semiconductor, ADM1026JSTZ-REEL Datasheet - Page 37
![IC CNTRL SYS REF/EEPROM 48-LQFP](/photos/7/49/74961/adm1026jstz_sml.jpg)
ADM1026JSTZ-REEL
Manufacturer Part Number
ADM1026JSTZ-REEL
Description
IC CNTRL SYS REF/EEPROM 48-LQFP
Manufacturer
ON Semiconductor
Datasheet
1.ADM1026JSTZ-R7.pdf
(55 pages)
Specifications of ADM1026JSTZ-REEL
Function
Hardware Monitor
Topology
ADC, Comparator, Multiplexer, Register Bank
Sensor Type
External & Internal
Sensing Temperature
0°C ~ 100°C, External Sensor
Output Type
SMBus™
Output Alarm
No
Output Fan
Yes
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
0°C ~ 100°C
Mounting Type
Surface Mount
Package / Case
48-LFQFP
Full Temp Accuracy
+/- 3 C
Digital Output - Bus Interface
Serial (2-Wire)
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
0 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADM1026JSTZ-REEL
Manufacturer:
AD
Quantity:
6 906
Company:
Part Number:
ADM1026JSTZ-REEL
Manufacturer:
ON Semiconductor
Quantity:
10 000
Part Number:
ADM1026JSTZ-REEL
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
ADM1026JSTZ-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Detailed Register Descriptions
Table 10. Register 00h, Configuration Register 1 (Power−On Default 00h)
Table 11. Register 01h, Configuration Register 2 (Power−On Default 00h)
Bit
Bit
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Enable Voltage/Ext2 = 0
Enable GPIO0/Fan0 = 0
Enable GPIO1/Fan1 = 0
Enable GPIO2/Fan2 = 0
Enable GPIO3/Fan3 = 0
Enable GPIO4/Fan4 = 0
Enable GPIO5/Fan5 = 0
Enable GPIO6/Fan6 = 0
Enable GPIO7/Fan7 = 0
Enable PWM AFC = 0
Enable DAC AFC = 0
Enable THERM = 0
Software Reset = 0
Int Enable = 0
Int Clear = 0
Monitor = 0
Name
Name
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
When this bit is set the ADM1026 monitors all voltage, temperature and fan
channels in a round robin manner.
When this bit is set, the INT output pin is enabled.
Setting this bit clears an interrupt from the voltage, temperature or fan speed
channels. Because GPIO interrupts are level triggered, this bit has no effect on
interrupts originating from GPIO channels. This bit is cleared by writing a 0 to it. If
in monitoring mode voltages, temperatures and fan speeds continue to be
monitored after writing to this bit to clear an interrupt, so an interrupt may be set
again on the next monitoring cycle.
When this bit is 1, the ADM1026 monitors voltage (A
and 27, respectively. When this bit is 0, the ADM1026 monitors a second thermal
diode temperature channel, D2, on these pins. If the second thermal diode channel
is not being used, it is recommended that the bit be set to 1.
When this bit is 1, the THERM pin (Pin 42) is asserted (go low) if any of the
THERM limits are exceeded. If THERM is pulled low as an input, the DAC and
PWM outputs are forced to full scale until THERM is taken high.
When this bit is 1, the DAC output is enabled for automatic fan speed control
(AFC) based on temperature. When this bit is 0, the DAC Output reflects the value
in Reg 04h, the DAC Control Register.
When this bit is 1, the PWM output is enabled for automatic fan speed control
(AFC) based on temperature. When this bit is 0, the PWM Output reflects the value
in Reg 05h, the PWM Control Register.
Writing a 1 to this bit restores all registers to the power−on defaults. This bit is
cleared by writing a 0 to it. For more info, see the Software Reset Function section.
When this bit is 1, Pin 3 is enabled as a general−purpose I/O pin (GPIO0),
otherwise it is a fan tach measurement input (Fan 0).
When this bit is 1, Pin 4 is enabled as a general−purpose I/O pin (GPIO1),
otherwise it is a fan tach measurement input (Fan 1).
When this bit is 1, Pin 5 is enabled as a general−purpose I/O pin (GPIO2),
otherwise it is a fan tach measurement input (Fan 2).
When this bit is 1, Pin 6 is enabled as a general−purpose I/O pin (GPIO3),
otherwise it is a fan tach measurement input (Fan 3).
When this bit is 1, Pin 9 is enabled as a general−purpose I/O pin (GPIO4),
otherwise it is a fan tach measurement input (Fan 4).
When this bit is 1, Pin 10 is enabled as a general−purpose I/O pin (GPIO5),
otherwise it is a fan tach measurement input (Fan 5).
When this bit is 1, Pin 11 is enabled as a general−purpose I/O pin (GPIO6),
otherwise it is a fan tach measurement input (Fan 6).
When this bit is 1, Pin 12 is enabled as a general−purpose I/O pin (GPIO7),
otherwise it is a fan tach measurement input (Fan 7).
http://onsemi.com
37
Description
Description
IN8
and A
IN9
) on Pins 28