ADM1026JSTZ-REEL ON Semiconductor, ADM1026JSTZ-REEL Datasheet - Page 11
![IC CNTRL SYS REF/EEPROM 48-LQFP](/photos/7/49/74961/adm1026jstz_sml.jpg)
ADM1026JSTZ-REEL
Manufacturer Part Number
ADM1026JSTZ-REEL
Description
IC CNTRL SYS REF/EEPROM 48-LQFP
Manufacturer
ON Semiconductor
Datasheet
1.ADM1026JSTZ-R7.pdf
(55 pages)
Specifications of ADM1026JSTZ-REEL
Function
Hardware Monitor
Topology
ADC, Comparator, Multiplexer, Register Bank
Sensor Type
External & Internal
Sensing Temperature
0°C ~ 100°C, External Sensor
Output Type
SMBus™
Output Alarm
No
Output Fan
Yes
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
0°C ~ 100°C
Mounting Type
Surface Mount
Package / Case
48-LFQFP
Full Temp Accuracy
+/- 3 C
Digital Output - Bus Interface
Serial (2-Wire)
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
0 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADM1026JSTZ-REEL
Manufacturer:
AD
Quantity:
6 906
Company:
Part Number:
ADM1026JSTZ-REEL
Manufacturer:
ON Semiconductor
Quantity:
10 000
Part Number:
ADM1026JSTZ-REEL
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
ADM1026JSTZ-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
ADM1026 is powered down, unlike the data in the volatile
registers. Although referred to as read−only memory, the
EEPROM can be written to (as well as read from) via the
serial bus in exactly the same way as the other registers. The
main differences between the EEPROM and other registers
are:
•
•
•
two key EEPROM memory characteristics: memory cycling
endurance and memory data retention.
cycled through many program, read, and erase cycles. In real
terms, a single endurance cycle is composed of four
independent, sequential events, as follows:
to FFh until a first fail is recorded, signifying the endurance
limit of the EEPROM memory.
programmed data over time. The EEPROM in the ADM1026
has been qualified in accordance with the formal JEDEC
Retention Lifetime Specification (A117) at a specific junction
temperature (T
retention time. As part of this qualification procedure, the
EEPROM memory is cycled to its specified endurance limit
described above before data retention is characterized. This
means that the EEPROM memory is guaranteed to retain its
data for its full specified retention lifetime every time the
EEPROM is reprogrammed. Note that retention lifetime
based on an activation energy of 0.6 V derates with T
shown in Figure 15.
The EEPROM in the ADM1026 has been qualified for
Endurance qualifies the ability of the EEPROM to be
In reliability qualification, every byte is cycled from 00h
Retention quantifies the ability of the memory to retain its
An EEPROM location must be blank before it can be
written to. If it contains data, it must first be erased.
Writing to EEPROM is slower than writing to RAM.
Writing to the EEPROM should be restricted because
its typical cycle life is 100,000 write operations, due to
the usual EEPROM wear−out mechanisms.
Figure 15. Typical EEPROM Memory Retention
1. Initial page erase sequence
2. Read/verify sequence
3. Program sequence
4. Second read/verify sequence
300
250
200
150
100
50
0
40
50
J
= 55°C) to guarantee a minimum of 10 years
60
JUNCTION TEMPERATURE (5C)
70
80
90
100
110
http://onsemi.com
120
J
, as
11
Serial Bus Interface
system management bus (SMBus). The ADM1026 is
connected to this bus as a slave device, under the control of
a master device.
the device is powered on, it does so with a default serial bus
address. The 5 MSBs of the address are set to 01011, and the
2 LSBs are determined by the logical states of Pin 15
ADD/NTESTOUT. This pin is a three−state input that can be
grounded, connected to V
three different addresses.
(5Ch). ADD is sampled only at powerup on the first valid
SMBus transaction, so any changes made while the power
is on (and the address is locked) have no effect.
addresses allows the user to avoid conflicts with other
devices sharing the same serial bus, for example if more than
one ADM1026 is used in a system.
General SMBus Timing
read and write operations using the SMBus. The SMBus
specification defines specific conditions for different types
of read and write operations, which are discussed later in this
section. The general SMBus protocol* operates as follows:
Table 2. Address Pin Truth Table
GND
No Connect
V
Control of the ADM1026 is carried out via the serial
The ADM1026 has a 7−bit serial bus slave address. When
If ADD is left open−circuit, the default address is 0101110
The facility to make hardwired changes to device
Figure 16 and Figure 17 show timing diagrams for general
CC
1. The master initiates data transfer by establishing a
start condition, defined as a high−to−low transition
on the serial data line (SDA) while the serial clock
line SCL remains high. This indicates that a data
stream follows. All slave peripherals connected to
the serial bus respond to the start condition and
shift in the next 8 bits, consisting of a 7−bit slave
address (MSB first) and an R/W bit, which
determine the direction of the data transfer, that is,
whether data is written to or read from the slave
device (0 = write, 1 = read).
The peripheral whose address corresponds to the
trans−mitted address responds by pulling the data
line low during the low period before the ninth
clock pulse, known as the acknowledge bit, and
holding it low during the high period of this clock
pulse. All other devices on the bus remain idle
while the selected device waits for data to be read
from or written to it. If the R/W bit is 0, the master
writes to the slave device. If the R/W bit is 1, the
master reads from the slave device.
ADD Pin
CC
, or left open−circuit to give
A1
0
1
0
A0
0
0
1