ADM1026JSTZ-REEL ON Semiconductor, ADM1026JSTZ-REEL Datasheet - Page 32
![IC CNTRL SYS REF/EEPROM 48-LQFP](/photos/7/49/74961/adm1026jstz_sml.jpg)
ADM1026JSTZ-REEL
Manufacturer Part Number
ADM1026JSTZ-REEL
Description
IC CNTRL SYS REF/EEPROM 48-LQFP
Manufacturer
ON Semiconductor
Datasheet
1.ADM1026JSTZ-R7.pdf
(55 pages)
Specifications of ADM1026JSTZ-REEL
Function
Hardware Monitor
Topology
ADC, Comparator, Multiplexer, Register Bank
Sensor Type
External & Internal
Sensing Temperature
0°C ~ 100°C, External Sensor
Output Type
SMBus™
Output Alarm
No
Output Fan
Yes
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
0°C ~ 100°C
Mounting Type
Surface Mount
Package / Case
48-LFQFP
Full Temp Accuracy
+/- 3 C
Digital Output - Bus Interface
Serial (2-Wire)
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
0 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADM1026JSTZ-REEL
Manufacturer:
AD
Quantity:
6 906
Company:
Part Number:
ADM1026JSTZ-REEL
Manufacturer:
ON Semiconductor
Quantity:
10 000
Part Number:
ADM1026JSTZ-REEL
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
ADM1026JSTZ-REEL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Reduced Power Mode
setting Bit 0 of the configuration register to 0. This disables
the internal ADC.
Software Reset Function
software by setting Bit 7 of Configuration Register 1
(Reg. 00h) to 1. Configuration Register 1, 00h, should then
be manually cleared. Note that the software reset differs
from a power−on reset in that only some of the ADM1026
registers are reinitialized to their power−on default values.
The registers that are initialized to their default values by the
software reset are
•
•
•
•
The ADM1026 can be placed in a low power mode by
As previously mentioned, the ADM1026 can be reset in
Configuration Registers (Registers 01h to 0Bh)
Mask Registers 1 to 6, internal temperature offset, and
Status Registers 4, 5, and 6 (Registers 18h to 25h)
All value registers (Registers 1Fh, 20h to 3Fh)
External 1 and External 2 Offset Registers (6Eh, 6Fh)
http://onsemi.com
32
not reset by the software reset function. This can be useful
if one needs to reset the part but does not want to reprogram
all parameters again. Note that a power−on reset initializes
all registers on the ADM1026, including the limit registers.
Application Schematic
application that requires system management of a PC or
server. Several GPIOs are used to read the VID codes of the
CPU. Up to two CPU temperature measurements can be read
back. All power supply voltages are monitored in the
system. Up to eight fan speeds can be measured, irrespective
of whether they are controlled by the ADM1026 or
hardwired to a system supply. The V
recommended filtering circuitry.
Note that the limit registers (0Dh to 12h, 40h to 6Dh) are
Figure 61 shows how the ADM1026 could be used in an
REF
output includes the