S9S08SG8E2VTJR Freescale Semiconductor, S9S08SG8E2VTJR Datasheet - Page 34

no-image

S9S08SG8E2VTJR

Manufacturer Part Number
S9S08SG8E2VTJR
Description
8-bit Microcontrollers - MCU 9S08 UC W/ 8K 0.25UM SGF
Manufacturer
Freescale Semiconductor
Datasheet

Specifications of S9S08SG8E2VTJR

Rohs
yes
Core
HCS08
Data Bus Width
8 bit
Maximum Clock Frequency
40 MHz
Program Memory Size
8 KB
Data Ram Size
512 B
On-chip Adc
Yes
Operating Temperature Range
- 40 C to + 85 C
Package / Case
TSSOP-20
Mounting Style
SMD/SMT
A/d Bit Size
10 bit
A/d Channels Available
12
Interface Type
I2C, SCI, SPI
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
16
Number Of Timers
3
Program Memory Type
Flash
Supply Voltage - Max
5.5 V
Supply Voltage - Min
2.7 V

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S9S08SG8E2VTJR
Manufacturer:
FREESCALE
Quantity:
20 000
Chapter 2 Pins and Connections
Typically, application systems have two separate capacitors across the power pins. In this case, there
should be a bulk electrolytic capacitor, such as a 10-μF tantalum capacitor, to provide bulk charge storage
for the overall system and a 0.1-μF ceramic bypass capacitor located as near to the MCU power pins as
practical to suppress high-frequency noise. Each pin must have a bypass capacitor for best noise
suppression.
V
ADC module. A 0.1 μF ceramic bypass capacitor should be located as near to the MCU power pins as
practical to suppress high-frequency noise. The V
voltage reference low inputs, respectively for the ADC module. For this MCU, V
pin and these pins are available only in the 28-pin packages. In the 16-pin and 20-pin packages, they are
double bonded to the V
in the 28-pin packages. In the 16-pin and 20-pin packages, they are double bonded to the V
2.2.2
Immediately after reset, the MCU uses an internally generated clock provided by the clock source
generator (ICS) module. For more information on the ICS, see
(S08ICSV2).”
The oscillator (XOSC) in this MCU is a Pierce oscillator that can accommodate a crystal or ceramic
resonator. Rather than a crystal or ceramic resonator, an external oscillator can be connected to the EXTAL
input pin.
Refer to
resistors such as carbon composition resistors. Wire-wound resistors, and some metal film resistors, have
too much inductance. C1 and C2 normally should be high-quality ceramic capacitors that are specifically
designed for high-frequency applications.
R
is not generally critical. Typical systems use 1 MΩ to 10 MΩ. Higher values are sensitive to humidity and
lower values reduce gain and (in extreme cases) could prevent startup.
C1 and C2 are typically in the 5-pF to 25-pF range and are chosen to match the requirements of a specific
crystal or resonator. Be sure to take into account printed circuit board (PCB) capacitance and MCU pin
capacitance when selecting C1 and C2. The crystal manufacturer typically specifies a load capacitance
which is the series combination of C1 and C2 (which are usually the same size). As a first-order
approximation, use 10 pF as an estimate of combined pin and PCB capacitance for each oscillator pin
(EXTAL and XTAL).
2.2.3
RESET is a dedicated pin with open-drain drive containing an internal pull-up device. Internal power-on
reset and low-voltage reset circuitry typically make external reset circuitry unnecessary. This pin is
normally connected to the standard 6-pin background debug connector so a development system can
directly reset the MCU system. If desired, a manual external reset can be added by supplying a simple
switch to ground (pull reset pin low to force a reset).
28
F
DDA
is used to provide a bias path to keep the EXTAL input in its linear range during crystal startup; its value
and V
Figure 2-4
Oscillator (XOSC)
RESET
SSA
are the analog power supply pins for MCU. This voltage source supplies power to the
for the following discussion. R
DD
pin. For this MCU, V
MC9S08SG32 Data Sheet, Rev. 8
SSA
REFH
S
shares the V
(when used) and R
and V
REFL
Chapter 11, “Internal Clock Source
REFL
pins are the voltage reference high and
pin and these pins are available only
F
should be low-inductance
DDA
Freescale Semiconductor
shares the V
SS
pin.
REFH

Related parts for S9S08SG8E2VTJR