S9S08SG8E2VTJR Freescale Semiconductor, S9S08SG8E2VTJR Datasheet - Page 259

• Manufacturer Part Number: S9S08SG8E2VTJR
• Description: 8-bit Microcontrollers - MCU 9S08 UC W/ 8K 0.25UM SGF
• Manufacturer: Freescale Semiconductor

Specifications of S9S08SG8E2VTJR

• Rohs: yes
• Core: HCS08
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Program Memory Size: 8 KB
• Data Ram Size: 512 B
• On-chip Adc: Yes
• Operating Temperature Range: - 40 C to + 85 C
• Package / Case: TSSOP-20
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Interface Type: I2C, SCI, SPI
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 2.7 V

Reset the TPM counter before writing to the TPM modulo registers to avoid confusion about when the first
counter overflow will occur.
16.3.4
TPMxCnSC contains the channel-interrupt-status flag and control bits used to configure the interrupt
enable, channel configuration, and pin function.
Freescale Semiconductor
Reset
Reset
CHnIE
CHnF
MSnB
Field
W
W
7
6
5
R
R
CHnF
Bit 7
Channel n flag. When channel n is an input-capture channel, this read/write bit is set when an active edge occurs
on the channel n pin. When channel n is an output compare or edge-aligned/center-aligned PWM channel, CHnF
is set when the value in the TPM counter registers matches the value in the TPM channel n value registers. When
channel n is an edge-aligned/center-aligned PWM channel and the duty cycle is set to 0% or 100%, CHnF will
not be set even when the value in the TPM counter registers matches the value in the TPM channel n value
registers.
A corresponding interrupt is requested when CHnF is set and interrupts are enabled (CHnIE = 1). Clear CHnF by
reading TPMxCnSC while CHnF is set and then writing a logic 0 to CHnF. If another interrupt request occurs
before the clearing sequence is complete, the sequence is reset so CHnF remains set after the clear sequence
completed for the earlier CHnF. This is done so a CHnF interrupt request cannot be lost due to clearing a previous
CHnF.
Reset clears the CHnF bit. Writing a logic 1 to CHnF has no effect.
0 No input capture or output compare event occurred on channel n
1 Input capture or output compare event on channel n
Channel n interrupt enable. This read/write bit enables interrupts from channel n. Reset clears CHnIE.
0 Channel n interrupt requests disabled (use for software polling)
1 Channel n interrupt requests enabled
Mode select B for TPM channel n. When CPWMS=0, MSnB=1 configures TPM channel n for edge-aligned PWM
mode. Refer to the summary of channel mode and setup controls in
TPM Channel n Status and Control Register (TPMxCnSC)
0
0
0
7
7
Figure 16-12. TPM Channel n Status and Control Register (TPMxCnSC)
= Unimplemented or Reserved
CHnIE
6
0
0
6
6
Table 16-6. TPMxCnSC Field Descriptions
MSnB
5
5
0
5
0
MC9S08SG32 Data Sheet, Rev. 8
MSnA
4
0
0
4
4
Description
ELSnB
3
0
0
3
3
Table
Chapter 16 Timer/PWM Module (S08TPMV3)
ELSnA
2
0
0
2
2
16-7.
1
1
0
1
0
0
Bit 0
0
0
0
0
0
253