LPC1113FHN33/303,5 NXP Semiconductors, LPC1113FHN33/303,5 Datasheet - Page 250
LPC1113FHN33/303,5
Manufacturer Part Number
LPC1113FHN33/303,5
Description
ARM Microcontrollers - MCU Cortex-M0 24 kB flash up to 8kB SRAM
Manufacturer
NXP Semiconductors
Datasheet
1.LPC1113FHN333035.pdf
(538 pages)
Specifications of LPC1113FHN33/303,5
Rohs
yes
Core
ARM Cortex M0
Processor Series
LPC1113
Data Bus Width
32 bit
Maximum Clock Frequency
50 MHz
Program Memory Size
24 KB
Data Ram Size
4 KB
On-chip Adc
Yes
Operating Supply Voltage
1.8 V to 3.6 V
Operating Temperature Range
- 65 C to + 150 C
Package / Case
HVQFN-33
Mounting Style
SMD/SMT
Factory Pack Quantity
260
- Current page: 250 of 538
- Download datasheet (5Mb)
NXP Semiconductors
UM10398
User manual
15.10.1 Master Transmitter mode
Table 233. Abbreviations used to describe an I
In
The numbers in the circles show the status code held in the STAT register. At these points,
a service routine must be executed to continue or complete the serial transfer. These
service routines are not critical since the serial transfer is suspended until the serial
interrupt flag is cleared by software.
When a serial interrupt routine is entered, the status code in STAT is used to branch to the
appropriate service routine. For each status code, the required software action and details
of the following serial transfer are given in tables from
In the master transmitter mode, a number of data bytes are transmitted to a slave receiver
(see
initialized as follows:
Table 234. I2C0CONSET used to initialize Master Transmitter mode
The I
to logic 1 to enable the I
its own slave address or the General Call address in the event of another device
becoming master of the bus. In other words, if AA is reset, the I
slave mode. STA, STO, and SI must be reset.
Abbreviation
S
SLA
R
W
A
A
Data
P
Bit
Symbol
Value
Figure 53
Figure
2
C rate must also be configured in the SCLL and SCLH registers. I2EN must be set
7
-
-
53). Before the master transmitter mode can be entered, I2CON must be
to
Figure
All information provided in this document is subject to legal disclaimers.
Rev. 12 — 24 September 2012
6
I2EN
1
57, circles are used to indicate when the serial interrupt flag is set.
Explanation
START Condition
7-bit slave address
Read bit (HIGH level at SDA)
Write bit (LOW level at SDA)
Acknowledge bit (LOW level at SDA)
Not acknowledge bit (HIGH level at SDA)
8-bit data byte
STOP condition
2
C block. If the AA bit is reset, the I
5
STA
0
Chapter 15: LPC111x/LPC11Cxx I2C-bus controller
4
STO
0
2
C operation
3
SI
0
Table 235
2
C block will not acknowledge
2
AA
x
2
C interface cannot enter
to
Table
UM10398
1
-
-
© NXP B.V. 2012. All rights reserved.
241.
0
-
-
250 of 538
Related parts for LPC1113FHN33/303,5
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: