DSPIC30F6010A MICROCHIP [Microchip Technology], DSPIC30F6010A Datasheet - Page 187

• Manufacturer Part Number: DSPIC30F6010A
• Description: High-Performance, 16-bit Digital Signal Controllers
• Manufacturer: MICROCHIP [Microchip Technology]

TABLE 24-14: EXTERNAL CLOCK TIMING REQUIREMENTS
© 2011 Microchip Technology Inc.
AC CHARACTERISTICS
OS10
OS20
OS25
OS30
OS31
OS40
OS41
Note 1:
Param
No.
2:
3:
4:
5:
6:
F
T
T
TosL,
TosH
TosR,
TosF
TckR
TckF
Symb
Data in “Typ” column is at 5V, 25°C unless otherwise stated. Parameters are for design guidance only and
are not tested.
These parameters are characterized but not tested in manufacturing.
Limited by the PLL output frequency range.
Limited by the PLL input frequency range.
Instruction cycle period (T
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits may result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at “min.”
values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the
“Max.” cycle time limit is “DC” (no clock) for all devices.
Measurements are taken in EC or ERC modes. The CLKO signal is measured on the OSC2 pin. CLKO is
low for the Q1-Q2 period (1/2 T
OSC
CY
OSC
ol
External CLKN Frequency
(External clocks allowed only
in EC mode)
Oscillator Frequency
T
Instruction Cycle Time
External Clock
High or Low Time
External Clock
Rise or Fall Time
CLKO Rise Time
CLKO Fall Time
OSC
= 1/F
Characteristic
OSC
(2)
(2)
(2)(6)
(2)(6)
in (OSC1)
in (OSC1)
CY
) equals four times the input oscillator time base period. All specified values
(2)
(2)(5)
CY
) and high for the Q3-Q4 period (1/2 T
(2)
Standard Operating Conditions: 2.5V to 5.5V
(unless otherwise stated)
Operating temperature
.45 x T
12
12
12
Min
DC
DC
0.4
10
10
10
10
—
—
33
—
—
—
4
4
4
4
4
4
4
(4)
(4)
(4)
OSC
dsPIC30F6010A/6015
32.768
Typ
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
(1)
22.5
7.5
7.5
20
20
15
Max
-40°C ≤ T
-40°C ≤ T
DC
40
10
10
10
10
10
25
25
25
20
—
—
—
—
—
4
4
(4)
(4)
(3)
(3)
(3)
(3)
CY
).
Units
A
A
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
kHz
—
ns
ns
ns
ns
ns
≤ +85°C for Industrial
≤ +125°C for Extended
EC
EC with 4x PLL
EC with 8x PLL
EC with 16x PLL
RC
XTL
XT
XT with 4x PLL
XT with 8x PLL
XT with 16x PLL
HS
HS/2 with 4x PLL
HS/2 with 8x PLL
HS/2 with 16x PLL
HS/3 with 4x PLL
HS/3 with 8x PLL
HS/3 with 16x PLL
LP
See parameter OS10
for F
See
EC
EC
See parameter
See parameter DO32
OSC
Table 24-16
DS70150E-page 187
Conditions
value
DO31