MC68HC912D60A MOTOROLA [Motorola, Inc], MC68HC912D60A Datasheet - Page 46
MC68HC912D60A
Manufacturer Part Number
MC68HC912D60A
Description
Microcontrollers
Manufacturer
MOTOROLA [Motorola, Inc]
Datasheet
1.MC68HC912D60A.pdf
(460 pages)
- Current page: 46 of 460
- Download datasheet (4Mb)
Pinout and Signal Descriptions
Technical Data
46
output to indicate that an internal failure has been detected in either the
clock monitor or COP watchdog circuit. The MCU goes into reset
asynchronously and comes out of reset synchronously. This allows the
part to reach a proper reset state even if the clocks have failed, while
allowing synchronized operation when starting out of reset.
It is important to use an external low-voltage reset circuit (such as
MC34064 or MC34164) to prevent corruption of RAM or EEPROM due
to power transitions.
The reset sequence is initiated by any of the following events:
External circuitry connected to the reset pin should not include a large
capacitance that would interfere with the ability of this signal to rise to a
valid logic one within nine bus cycles after the low drive is released.
Upon detection of any reset, an internal circuit drives the reset pin low
and a clocked reset sequence controls when the MCU can begin normal
processing. In the case of POR or a clock monitor error, a 4096 cycle
oscillator startup delay is imposed before the reset recovery sequence
starts (reset is driven low throughout this 4096 cycle delay). The internal
reset recovery sequence then drives reset low for 16 to 17 cycles and
releases the drive to allow reset to rise. Nine cycles later this circuit
samples the reset pin to see if it has risen to a logic one level. If reset is
low at this point, the reset is assumed to be coming from an external
request and the internally latched states of the COP timeout and clock
monitor failure are cleared so the normal reset vector ($FFFE:FFFF) is
taken when reset is finally released. If reset is high after this nine cycle
delay, the reset source is tentatively assumed to be either a COP failure
or a clock monitor fail. If the internally latched state of the clock monitor
fail circuit is true, processing begins by fetching the clock monitor vector
($FFFC:FFFD). If no clock monitor failure is indicated, and the latched
state of the COP timeout is true, processing begins by fetching the COP
•
•
•
•
Freescale Semiconductor, Inc.
For More Information On This Product,
Power-on-reset (POR)
COP watchdog enabled and watchdog timer times out
Clock monitor enabled and Clock monitor detects slow or stopped
clock
User applies a low level to the reset pin
Pinout and Signal Descriptions
Go to: www.freescale.com
MC68HC912D60A — Rev 3.0
MOTOROLA
Related parts for MC68HC912D60A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Motorola, Inc [VOLTAGE REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
6367254 MOTOROLA SC (XSTRS/R F)
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
MC1494LMotorola, Inc [MONOLITHIC FOUR-QUADRANT MULTIPLIER]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC1466LMotorola, Inc [PRECISION WIDE RANGE VOLTAGE AND CURRENT REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MC145532DWMotorola, Inc [ADPCM Transcoder]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Silicon Controlled Rectifiers
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF Power Field Effect Transistors N-Channel Enhancement-Mode Lateral MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTORS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
LATERAL N-CHANNEL BROADBAND RF POWER MOSFETs
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF POWER FIELD EFFECT TRANSISTOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
RF LOW POWER TRANSISTOR NPN SILICON
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
PLASTIC SURFACE MOUNT ZENER DIODES 1.5 WATTS 3.3-68 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
OVERVOLTAGE TRANSIENT SUPPRESSOR
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET 15 AMPERES 60 VOLTS
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet:
Part Number:
Description:
TMOS POWER FET LOGIC LEVEL 19 AMPERES 30 VOLTS RDS(on) = 0.099 OHM
Manufacturer:
MOTOROLA [Motorola, Inc]
Datasheet: