PCF2127AT/1 NXP [NXP Semiconductors], PCF2127AT/1 Datasheet - Page 55
PCF2127AT/1
Manufacturer Part Number
PCF2127AT/1
Description
Integrated RTC, TCXO and quartz crystal
Manufacturer
NXP [NXP Semiconductors]
Datasheet
1.PCF2127AT1.pdf
(80 pages)
- Current page: 55 of 80
- Download datasheet (536Kb)
NXP Semiconductors
PCF2127A_2
Product data sheet
9.1.1 Data transmission
9.1 SPI-bus interface
Data transfer to and from the device is made via a 3 wire SPI-bus (see
lines for input and output are split. The data input and output line can be connected
together to facilitate a bidirectional data bus (see
whenever the chip enable line pin SDA/CE is inactive.
Table 57.
[1]
The chip enable signal is used to identify the transmitted data. Each data transfer is a
byte, with the Most Significant Bit (MSB) sent first.
The transmission is controlled by the active LOW chip enable signal SDA/CE. The first
byte transmitted is the command byte. Subsequent bytes will be either data to be written
or data to be read (see
The command byte defines the address of the first register to be accessed and the
read/write mode. The address counter will auto increment after every access and will
reset to zero after the last valid register is accessed. The R/W bit defines if the following
bytes will be read or write information.
Symbol
SDA/CE
SCL
SDI
SDO
Fig 34. SDI, SDO configurations
Fig 35. Data transfer overview
The chip enable must not be wired permanently LOW.
Serial interface
data bus
SDA/CE
Function
chip enable input;
active LOW
serial clock input
serial data input
serial data output
All information provided in this document is subject to legal disclaimers.
Figure
Rev. 02 — 7 May 2010
COMMAND
35).
two wire mode
SDO
SDI
DATA
[1]
Description
when HIGH, the interface is reset;
when SDA/CE is HIGH, input may float;
when SDA/CE is HIGH, input may float;
push-pull output;
input may be higher than V
input may be higher than V
input may be higher than V
input data is sampled on the rising edge of SCL
drives from V
output data is changed on the falling edge of SCL
Integrated RTC, TCXO and quartz crystal
single wire mode
SDO
SDI
DATA
Figure
001aai560
34). The SPI-bus is initialized
SS
to V
BBS
DATA
;
PCF2127A
DD
DD
DD
Table
© NXP B.V. 2010. All rights reserved.
;
013aaa311
57). The data
55 of 80
Related parts for PCF2127AT/1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: