at90pwm81-16se ATMEL Corporation, at90pwm81-16se Datasheet - Page 141
at90pwm81-16se
Manufacturer Part Number
at90pwm81-16se
Description
8-bit Avr Microcontroller With 8k Bytes In- System Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet
1.AT90PWM81-16SE.pdf
(323 pages)
- Current page: 141 of 323
- Download datasheet (6Mb)
7734M–AVR–03/10
The Input Control Registers are used to configure the 2 PSC’s Retrigger/Fault block A & B. The 2 blocks
are identical, so they are configured on the same way.
• Bit 7 – PCAEnx : PSC n Capture Enable Input Part x
Writing this bit to one enables the capture function when external event occurs on input selected as input
for Part x (see PISELnx1:0 bit in the same register).
• Bit 6 – PISELnx0 : PSC n Input Select for Part x
Together with PISELnx1 in PCNFEn register, defines active signal on PSC module A. See
page 138
• Bit 5 –PELEVnx0 : PSC n Edge Level Selector of Input Part x
Together with PELEVnx1 n PCNFEn register, defines active edge & level on PSC part x ; See
16 on page 138
• Bit 4 – PFLTEnx : PSC n Filter Enable on Input Part x
Setting this bit (to one) activates the Input Capture Noise Canceler. When the noise canceler is activated,
the input from the retrigger pin is filtered. The filter function requires four successive equal valued sam-
ples of the retrigger pin for changing its output. The Input Capture is therefore delayed by four oscillator
cycles when the noise canceler is enabled.
• Bit 3:0 – PRFMnx3:0: PSC n Fault Mode
These four bits define the mode of operation of the Fault or Retrigger functions.
(see PSC Functional Specification for more explanations)
Table 13-21.
PRFMnx3:0
0000b
0001b
0010b
0011b
0100b
0101b
0110b
0111b
1000b
1001b
and
Table 13-19 on page 139
and
Level Sensitivity and Fault Mode Operation
Description
No action, PSC Input is ignored
PSC Input Mode 1: Stop signal, Jump to Opposite Dead-Time and Wait
PSC Input Mode 2: Stop signal, Execute Opposite Pulse and Wait
PSC Input Mode 3: Stop signal, Execute Opposite Pulse while Fault active
PSC Input Mode 4: Deactivate outputs without changing timing.
PSC Input Mode 5: Stop signal and Insert Dead-Time
PSC Input Mode 6: Stop signal, Jump to Opposite Dead-Time and Wait.
PSC Input Mode 7: Halt PSC and Wait for Software Action
PSC Input Mode 8: Edge Retrigger PSC
PSC Input Mode 9: Fixed Frequency Edge Retrigger PSC
Table 13-17 on page 138
AT90PWM81
Table 13-18 on
Table 13-
141
Related parts for at90pwm81-16se
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: