adsp-21364bbc Analog Devices, Inc., adsp-21364bbc Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
adsp-21364bbc
Manufacturer Part Number
adsp-21364bbc
Description
Sharc Processor
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADSP-21364BBC.pdf
(56 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
adsp-21364bbcZ-1AA
Manufacturer:
Analog Devices Inc
Quantity:
10 000
ADSP-21362/ADSP-21363/ADSP-21364/ADSP-21365/ADSP-21366
Table 4. Pin Descriptions (Continued)
1
2
3
4
Pin
RESETOUT/CLKOUT O
RESET
TCK
TMS
TDI
TDO
TRST
EMU
V
V
A
A
GND
RD, WR, and ALE are three-stated (and not driven) only when RESET is active.
Output only is a three-state driver with its output path always enabled.
Three-state is a three-state driver with pull-up disabled.
Input only is a three-state driver with both output path and pull-up disabled.
DDINT
DDEXT
VDD
VSS
Type
I/A
I
I/S
(pu)
I/S
(pu)
O
I/A
(pu)
O (O/D)
(pu)
P
P
P
G
G
State During and
After Reset
Output only
Input only
Input only
Three-state with
pull-up enabled
Three-state with
pull-up enabled
Three-state
Three-state with
pull-up enabled
Three-state with
pull-up enabled
3
4
Rev. D | Page 14 of 56 | April 2008
Function
Reset Out/Local Clock Out. Drives out the core reset signal to an external device.
CLKOUT can also be configured as a reset out pin. The functionality can be switched
between the PLL output clock and reset out by setting Bit 12 of the PMCTL register.
The default is reset out.
Processor Reset. Resets the ADSP-2136x to a known state. Upon deassertion, there is
a 4096 CLKIN cycle latency for the PLL to lock. After this time, the core begins program
execution from the hardware reset vector address. The RESET input must be asserted
(low) at power-up.
Test Clock (JTAG). Provides a clock for JTAG boundary scan. TCK must be asserted
(pulsed low) after power-up or held low for proper operation of the processors.
Test Mode Select (JTAG). Used to control the test state machine. TMS has a 22.5 kΩ
internal pull-up resistor.
Test Data Input (JTAG). Provides serial data for the boundary scan logic. TDI has a
22.5 kΩ internal pull-up resistor.
Test Data Output (JTAG). Serial scan output of the boundary scan path.
Test Reset (JTAG). Resets the test state machine. TRST must be asserted (pulsed low)
after power-up or held low for proper operation of the ADSP-2136x. TRST has a
22.5 kΩ internal pull-up resistor.
Emulation Status. Must be connected to the processor’s JTAG emulators target board
connector only. EMU has a 22.5 kΩ internal pull-up resistor.
Core Power Supply. Nominally +1.2 V dc for the K, B grade models, and 1.0 V dc for
the Y grade models, and supplies the processor’s core (13 pins).
I/O Power Supply. Nominally +3.3 V dc (6 pins).
Analog Power Supply. Nominally +1.2 V dc for the K, B grade models, and 1.0 V dc for
the Y grade models, and supplies the processor’s internal PLL (clock generator). This
pin has the same specifications as V
required.
Analog Power Supply Return.
Power Supply Return. (54 pins)
For more information, see Power Supplies on Page 9.
DDINT
, except that added filtering circuitry is